Body › Car door › Repair
左后门总成 · T00617973

 Left rear door assembly左后门总成

Removal procedure拆卸程序
1. Preparation1. 准备工作
1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面,启用驻车制动,使整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
2. Remove the left rear door switch panel assembly2. 拆卸左后门开关面板总成
3. Remove the left rear door trim panel assembly3. 拆卸左后门饰板总成
4. Remove the waterproof membrane in front of the left rear door4. 拆卸左后门前防水膜
5. Remove the left rear door rear waterproof membrane5. 拆卸左后门后防水膜
6. Remove the woofer assembly (left rear door)6. 拆卸低音扬声器总成(左后门)
7. Remove the inner water cutter of the left rear door7. 拆卸左后门内水切
8. Remove the left rear door outer water cutter8. 拆卸左后门外水切
9. Remove the left rear door glass assembly9. 拆卸左后门玻璃总成
10. Remove the left rear door glass lifter assembly10. 拆卸左后门玻璃升降器总成
11. Remove the left rear door lock assembly11. 拆卸左后门锁总成
12. Remove the left rear door outer handle assembly12. 拆卸左后门外把手总成
13. Remove the left rear door stopper assembly13. 拆卸左后门限位器总成
14. Remove the left rear door rear assembly guide rail assembly14. 拆卸左后门后部总装导轨总成
15. Remove the lower rear sealing strip of the left rear door15. 拆卸左后门后下密封条
16. Remove the left rear door rubber strip16. 拆卸左后门胶条
17. Remove the left rear door glass sliding strip17. 拆卸左后门玻璃滑动胶条
18. Remove the left rear door frame B-pillar triangle block18. 拆卸左后门框B柱三角块
19. Remove the upper left rear door buffer block19. 拆卸左后侧门上缓冲块
20. Remove the left rear door assembly20. 拆卸左后门总成
Graphic
1 Loosen the 2 bolts ① of the upper and lower hinges.拧松上、下铰链2颗螺栓①。
Recommended tools: E8 socket推荐工具:E8套筒
2 Disconnect the wiring harness fixing clip and take out the left rear door wiring harness from the door.断开线束固定卡,将左后门线束从车门取出。
3 Lift the left rear door assembly upward to remove the left rear door assembly from its installation position, and then remove the left rear door assembly.向上抬起左后门总成,使左后门总成脱离安装位置,取下左后门总成。
  Note:提示:
♦  This step is difficult to operate by one person and requires the cooperation of an assistant.此步骤一人操作较难,需助手协同合作。
4 Remove the left rear door upper hinge (door side).拆卸左后门上铰链(车门侧)。
5 Remove the left rear door lower hinge (door side).拆卸左后门下铰链(车门侧)。
Installation procedure安装程序
1. Install the left rear door assembly1. 安装左后门总成
1 Install the left rear door lower hinge (door side).安装左后门下铰链(车门侧)。
2 Install the left rear door upper hinge (door side).安装左后门上铰链(车门侧)。
3 Lift the left rear door assembly to the installation position, place and adjust the left rear door wiring harness to the left rear door assembly.抬动左后门总成到安装位置,放置并调整左后门线束到左后门总成。
  Note:提示:
♦  This step is difficult to operate by one person and requires the cooperation of an assistant.此步骤一人操作较难,需助手协同合作。
Graphic
4 Tighten the 2 bolts ① of the upper and lower hinges.拧紧上下铰链2颗螺栓①。
Recommended tools: E8 socket推荐工具:E8套筒
2. Install the left rear door upper buffer block2. 安装左后侧门上缓冲块
3. Install the left rear door frame B-pillar triangle block3. 安装左后门框B柱三角块
4. Install the sliding rubber strip on the left rear door window.4. 安装左后门玻璃滑动胶条
5. Install the left rear door rubber strip5. 安装左后门胶条
6. Install the lower rear left rear door sealing strip6. 安装左后门后下密封条
7. Install the left rear door rear assembly guide rail assembly7. 安装左后门后部总装导轨总成
8. Install the rear door stopper assembly8. 安装后门限位器总成
9. Install the left rear door outer handle assembly9. 安装左后门外把手总成
10. Install the left rear door lock assembly10. 安装左后门锁总成
11. Install the left rear door glass lifter assembly11. 安装左后门玻璃升降器总成
12. Install the left rear door glass assembly12. 安装左后门玻璃总成
13. Install the left rear door outer water cutter13. 安装左后门外水切
14. Install the left rear door inner water cutter14. 安装左后门内水切
15. Install the subwoofer assembly (left rear door)15. 安装低音扬声器总成(左后门)
16. Install the left rear door rear waterproof membrane16. 安装左后门后防水膜
17. Install the waterproof membrane in front of the left rear door17. 安装左后门前防水膜
18. Install the left rear door trim panel assembly18. 安装左后门饰板总成
19. Install the left rear door switch panel assembly19. 安装左后门开关面板总成
20. Connect the negative terminal of the 12V battery, start the vehicle, and check that the surface difference between the left rear door assembly and the body should be normal.20. 连接蓄电池负极,启动车辆,检查左后门总成与车身面差应正常