Left rear door trim panel assembly左后门饰板总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and turn the vehicle power supply to "OFF".将车辆停在平坦路面，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove the left rear door switch panel assembly2. 拆卸左后门开关面板总成 Reference: Left rear door switch panel assembly参考：左后门开关面板总成

3. Remove the left rear door trim panel assembly3. 拆卸左后门饰板总成

1 Pry open and remove the left rear door inner opening handle bolt cover A and the left rear door handle box bolt cover B.撬开并取下左后门内开拉手螺栓饰盖A、左后门拉手盒螺栓盖B。 Recommended tools: Interior parts removal tools推荐工具：内饰件拆卸工具

2 Remove the 2 fixing screws ①, insert a tool on the lower edge of the left rear door trim panel assembly and pry, disengage the left rear door trim panel fixed clip, lift up and remove the left rear door trim panel assembly.拆卸2颗固定螺钉①，在左后门饰板总成下边缘插入工具并撬动，脱开左后门饰板总固定卡扣，向上提起并取下左后门饰板总成。 Recommended tools: Phillips screwdriver, interior parts removal tool推荐工具：十字螺丝刀、内饰件拆卸工具   Note:提示： ♦  When removing the door trim panel assembly, avoid improper operation, which may cause the door lock cable to break.脱开门饰板总成时避免操作过当，导致门锁拉线扯断。 ♦  Pay attention to the clip position at 11 in the picture.注意图示11处卡扣位置。 3 Disconnect the connector from the left rear door trim assembly.断开与左后门饰板总成连接的接插件。

4 Disengage the door lock cable A and remove the left rear door trim panel assembly.脱开门锁拉线A，取下左后门饰板总成。

Installation procedure安装程序

1. Install the left rear door trim panel assembly1. 安装左后门饰板总成

1 Connect door lock cable A to the left rear door trim panel assembly.连接门锁拉线A到左后门饰板总成。   Note:提示： ♦  Check that the door lock cable should be securely installed.检查门锁拉线应安装牢固。 2 Connect the connector to the left rear door trim panel assembly.连接与左后门饰板总成连接的接插件。

3 Place and adjust the left rear door trim panel assembly to the installation position. Align with the 11 fixed clip positions in the figure and press firmly to ensure that it is installed in place. Install the 2 fixing screws ① and tighten them.放置并调整左后门饰板总成到安装位置，对准图示11处固定卡扣位置用力按压确保安装到位，安装2颗固定螺钉①并紧固。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

4 Install the left rear door inner opening handle bolt cover A and the left rear door handle box bolt cover B.安装左后门内开拉手螺栓饰盖A、左后门拉手盒螺栓盖B。

2. Install the left rear door switch panel assembly2. 安装左后门开关面板总成 Reference: Left rear door switch panel assembly参考：左后门开关面板总成

3. Connect the negative terminal of the 12V battery3. 连接蓄电池负极