Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
|
|
|
2. Remove the front left seat assembly2. 拆卸前排左座椅总成
|
|
|
3. Remove the driver's side lower left decorative panel assembly3. 拆卸驾驶侧左下装饰板总成
|
|
|
4. Remove the driver’s side lower cover panel assembly4. 拆卸驾驶侧下护板总成
|
|
|
5. Remove the left end cover assembly of the instrument panel5. 拆卸仪表板左侧端盖总成
|
|
|
6. Remove the left end cover of the instrument panel6. 拆卸仪表板左侧端盖盖板
|
|
|
7. Remove the left front inner sill trim panel assembly7. 拆卸左前内门槛饰板总成
|
|
|
8. Remove the second row seat cushion assembly8. 拆卸第二排座椅坐垫总成
|
|
|
9. Remove the left rear inner sill trim panel assembly9. 拆卸左后内门槛饰板总成
|
|
|
10. Remove the left B-pillar air outlet assembly10. 拆卸左侧B柱出风口总成
|
|
|
11. Remove the left B-pillar lower trim panel assembly11. 拆卸左B柱下饰板总成
|
|
|
12. Remove the left B-pillar air duct assembly12. 拆卸左侧B柱风管总成
|
|
|
13. Remove the first row left seat belt assembly13. 拆卸第一排左侧安全带总成
|
|
|
14. Remove the left rear door upper hinge14. 拆卸左后门上铰链
|
|
|
1 Lock the door and use a marker pen to mark the relative position A on the joint between the left rear door and the door frame.锁止车门，使用标记笔在左后车门与门框配合处做相对位置标记A。
|
|
|
2 Remove the fixing bolt ①.拆卸固定螺栓①。
|
|
Recommended tools: 13mm socket推荐工具：13mm套筒 |
|
|
|
3 Remove the fixing bolts ① and ②, and remove the left rear door upper hinge.拆卸固定螺栓①、固定螺栓②，取下左后门上铰链。
|
|
Recommended tools: 13mm socket推荐工具：13mm套筒 |
|
Installation procedure安装程序
|
|
1. Install the left rear door upper hinge1. 安装左后门上铰链
|
|
|
1 Place and adjust the left rear door upper hinge to the installation position, install and tighten the fixing bolts ① and ②.放置并调整左后门上铰链到安装位置，安装固定螺栓①、固定螺栓②并紧固。
|
|
Recommended tools: 13mm socket推荐工具：13mm套筒 |
|
|
Torque requirements: 50-60N·m②, 27-33N·m①扭矩要求：50-60N•m②、27-33N•m① |
|
|
|
2 Install the fixing bolts ① and tighten them.安装固定螺栓①并紧固。
|
|
Recommended tools: 13mm socket推荐工具：13mm套筒 |
|
|
Torque requirement: 27-33N·m扭矩要求：27-33N•m |
|
|
|
3 Adjust the left rear door making sure mark A is aligned.调整左后车门，确保标记A对齐。
|
|
|
2. Install the first row left seat belt assembly2. 安装第一排左侧安全带总成
|
|
|
3. Install the left B-pillar air duct assembly3. 安装左侧B柱风管总成
|
|
|
4. Install the left B-pillar lower trim panel assembly4. 安装左B柱下饰板总成
|
|
|
5. Install the left B-pillar air outlet assembly5. 安装左侧B柱出风口总成
|
|
|
6. Install the left rear inner sill trim panel assembly6. 安装左后内门槛饰板总成
|
|
|
7. Install the second row seat cushion assembly7. 安装第二排座椅坐垫总成
|
|
|
8. Install the left front inner sill trim panel assembly8. 安装左前内门槛饰板总成
|
|
|
9. Install the left end cover of the instrument panel9. 安装仪表板左侧端盖盖板
|
|
|
10. Install the left end cover assembly of the instrument panel10. 安装仪表板左侧端盖总成
|
|
|
11. Install the driver’s side lower cover panel assembly11. 安装驾驶侧下护板总成
|
|
|
12. Install the driver's side lower left decorative panel assembly12. 安装驾驶侧左下装饰板总成
|
|
|
13. Install the front left seat assembly13. 安装前排左座椅总成
|
|
|
14. Connect the negative terminal of the 12V battery, start the vehicle, and check that the left rear door opens and closes normally.14. 连接蓄电池负极，启动车辆，检查左后车门开合应正常
|
Left rear door upper hinge左后门上铰链
