Left rear door rear assembly guide rail assembly左后门后部总装导轨总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and turn the vehicle power supply to "OFF".将车辆停在平坦路面，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove the left rear door switch panel assembly2. 拆卸左后门开关面板总成 Reference: Left rear door switch panel assembly参考：左后门开关面板总成

3. Remove the left rear door trim panel assembly3. 拆卸左后门饰板总成 Reference: Left rear door trim panel assembly参考：左后门饰板总成

4. Remove the left rear door rear waterproof membrane4. 拆卸左后门后防水膜 Reference: Left rear door rear waterproof membrane参考：左后门后防水膜

5. Remove the inner water cutter of the left rear door5. 拆卸左后门内水切 Reference: Water cut inside the left rear door参考：左后门内水切

6. Remove the left rear door glass sliding strip6. 拆卸左后门玻璃滑动胶条 Reference: Left rear door glass sliding strip参考：左后门玻璃滑动胶条

7. Remove the left rear door rear assembly guide rail assembly7. 拆卸左后门后部总装导轨总成 1 Lower the left rear door glass assembly to the bottom.将左后门玻璃总成降到最下部。

2 Open the door sealing strip at the upper end of the rear assembly guide rail assembly of the left rear door, and remove the fixing screw ①.拨开左后门后部总装导轨总成上端区域的车门密封条，拆卸固定螺钉①。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

3 Pry open the blocking cover, remove the 2 fixing bolts ①, and take out the final assembly guide rail assembly at the rear of the left rear door.撬开堵盖，拆卸2颗固定螺栓①，取出左后门后部总装导轨总成。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install the left rear door rear assembly guide rail assembly1. 安装左后门后部总装导轨总成

1 Place and adjust the left rear door rear assembly guide rail assembly to the installation position, install 2 fixing bolts ① and tighten them.放置并调整左后门后部总装导轨总成到安装位置，安装2颗固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m

2 Install the fixing screw ① and tighten it, install the blocking cover, and reset the door seal.安装固定螺钉①并紧固，安装堵盖，复位车门密封条。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

2. Install the left rear door glass sliding strip2. 安装左后门玻璃滑动胶条 Reference: Left rear door glass sliding strip参考：左后门玻璃滑动胶条

3. Install the left rear door inner water cutter3. 安装左后门内水切 Reference: Water cut inside the left rear door参考：左后门内水切

4. Waterproof membrane installed on the left rear door4. 安装左后门后防水膜 Reference: Left rear door rear waterproof membrane参考：左后门后防水膜

5. Install the left rear door trim panel assembly5. 安装左后门饰板总成 Reference: Left rear door trim panel assembly参考：左后门饰板总成

6. Install the left rear door switch panel assembly6. 安装左后门开关面板总成 Reference: Left rear door switch panel assembly参考：左后门开关面板总成

7. Connect the negative terminal of the 12V battery, start the vehicle, and check that the left rear door glass should be working normally.7. 连接蓄电池负极，启动车辆，检查左后门玻璃应正常工作