Air conditioning high pressure pipe assembly Ⅰ空调高压管总成Ⅰ

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Recycle refrigerant2. 回收制冷剂 Reference: Recycling and recharging refrigerant参考：回收和加注制冷剂

3. Remove the front compartment front upper cover panel assembly3. 拆卸机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

4. Remove the left front wheel arch assembly4. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

5. Remove the right front wheel arch assembly5. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

6. Remove the front bumper assembly6. 拆卸前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成   Note:提示： ♦  Just remove the front bumper assembly and accessories as a whole without disassembling them.将前保险杠总成及附件整体拆下即可，不必进行拆分。

7. Remove the front-end module central support bracket assembly7. 拆卸前端模块中央支撑支架总成 Reference: Front-end module central support bracket assembly参考：前端模块中央支撑支架总成

8. Remove the filling port8. 拆卸加注口 Reference: Filling port参考：加注口

9. Disassemble the washing kettle assembly9. 拆卸洗涤水壶总成 Reference: Washing kettle assembly参考：洗涤水壶总成

10. Disassemble the woofer assembly (low speed beep)10. 拆卸低音扬声器总成(低速提示音) Reference: Subwoofer assembly (low speed beep)参考：低音扬声器总成(低速提示音)

11. Remove the front anti-collision beam assembly11. 拆卸前防撞梁总成 Reference: Front anti-collision beam assembly参考：前防撞梁总成

12. Remove the center lower air deflector12. 拆卸中央下部导流板 Reference: Center lower air deflector参考：中央下部导流板

13. Remove the active air intake grille13. 拆卸下主动进气格栅 Reference: Lower active air intake grille参考：下主动进气格栅

14. Disassemble the air conditioning high-pressure pipe assembly Ⅰ14. 拆卸空调高压管总成Ⅰ

1 Disconnect connector A, remove the fixing bolt ①, and disconnect the air-conditioning high-pressure pipe assembly Ⅰ from the condenser.断开接插件A，拆卸固定螺栓①，断开空调高压管总成Ⅰ与冷凝器的连接。 Recommended tools: 10mm socket推荐工具：10mm套筒

2 Remove the fixing bolts ①, disconnect the air-conditioning high-pressure pipe assembly I from the thermal management integrated module, and take out the air-conditioning high-pressure pipe assembly IA.拆卸固定螺栓①，断开空调高压管总成Ⅰ与热管理集成模块的连接，取出空调高压管总成ⅠA。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install air conditioning high-pressure pipe assembly Ⅰ1. 安装空调高压管总成Ⅰ

1 Place and adjust the air-conditioning high-pressure pipe assembly IA to the installation position, and connect the air-conditioning high-pressure pipe assembly IA to the thermal management integrated module.放置并调整空调高压管总成ⅠA到安装位置，连接空调高压管总成ⅠA到热管理集成模块。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m   Caution:注意： ♦  The O-ring of the air conditioning pipeline is a disposable part, please use new parts for each installation.空调管路O型圈为一次性部件，每次安装请使用新件。

2 Connect the air conditioning high-pressure pipe assembly I to the condenser, connect the connector A, install the fixing bolt ① and tighten it.连接空调高压管总成Ⅰ到冷凝器，连接接插件A，安装固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒

2. Install the lower active air intake grille2. 安装下主动进气格栅 Reference: Lower active air intake grille参考：下主动进气格栅

3. Install the center lower deflector3. 安装中央下部导流板 Reference: Center lower air deflector参考：中央下部导流板

4. Install the front anti-collision beam4. 安装前防撞梁 Reference: Front anti-collision beam assembly参考：前防撞梁总成

5. Install the woofer assembly (low speed beep)5. 安装低音扬声器总成(低速提示音) Reference: Subwoofer assembly (low speed beep)参考：低音扬声器总成(低速提示音)

6. Install the washing kettle assembly6. 安装洗涤水壶总成 Reference: Washing kettle assembly参考：洗涤水壶总成

7. Install the filling port7. 安装加注口 Reference: Filling port参考：加注口

8. Install the front-end module central support bracket assembly8. 安装前端模块中央支撑支架总成 Reference: Front-end module central support bracket assembly参考：前端模块中央支撑支架总成

9. Install the front bumper assembly9. 安装前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

10. Install the right front wheel arch assembly10. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

11. Install the left front wheel arch assembly11. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

12. Install the front compartment front upper cover panel assembly12. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

13. Add refrigerant13. 加注制冷剂 Reference: Recycling and recharging refrigerant参考：回收和加注制冷剂

14. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift14. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机