Front bumper assembly前保险杠总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the front compartment front upper cover panel assembly2. 拆卸机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

3. Remove the left front wheel arch assembly3. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

4. Remove the right front wheel arch assembly4. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

5. Remove the front bumper assembly5. 拆卸前保险杠总成

1 Remove a total of 6 fixing screws on the left and right ①.拆卸左右共6颗固定螺钉①。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

2 Remove the 7 fixing screws ①.拆卸7颗固定螺钉①。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

3 Remove the 4 fixing bolts ① to remove the front bumper assembly from the installation position, disconnect the two connectors of the front bumper assembly wiring harness, and remove the front bumper assembly.拆卸4颗固定螺栓①，使前保险杆总成脱离安装位置，断开前保险杠总成线束两个接插件，取下前保险杠总成。 Recommended tools: T30 socket推荐工具：T30套筒 4 Remove the front bumper camera assembly.拆卸前保险杠摄像头总成。 Reference: Front bumper camera assembly参考：前保险杠摄像头总成 5 Disassemble the front millimeter wave radar assembly.拆卸前保毫米波雷达总成。 Reference: Front protection millimeter wave radar assembly参考：前保毫米波雷达总成 6 Remove the front bumper ultrasonic radar assembly.拆卸前保险杠超声波雷达总成。 Reference: Front bumper ultrasonic radar assembly参考：前保险杠超声波雷达总成 7 Remove the main sensor for blind spot monitoring.拆卸盲区监测主传感器。 Reference: Blind spot monitoring main sensor参考：盲区监测主传感器 8 Main label before disassembly.拆卸前主标。 Reference: former subject参考：前主标 9 Remove the outside air temperature sensor assembly.拆卸外气温度传感器总成。 Reference: Outside air temperature sensor assembly参考：外气温度传感器总成

Installation procedure安装程序

1. Install the front bumper assembly1. 安装前保险杠总成 1 Install the front bumper camera assembly.安装前保险杠摄像头总成。 Reference: Front bumper camera assembly参考：前保险杠摄像头总成 2 Install the front protection millimeter wave radar assembly.安装前保毫米波雷达总成。 Reference: Front protection millimeter wave radar assembly参考：前保毫米波雷达总成 3 Install the front bumper ultrasonic radar assembly.安装前保险杠超声波雷达总成。 Reference: Front bumper ultrasonic radar assembly参考：前保险杠超声波雷达总成 4 Install the main sensor for blind spot monitoring.安装盲区监测主传感器。 Reference: Blind spot monitoring main sensor参考：盲区监测主传感器 5 Main label before installation.安装前主标。 Reference: former subject参考：前主标 6 Install the outside air temperature sensor assembly.安装外气温度传感器总成。 Reference: Outside air temperature sensor assembly参考：外气温度传感器总成 7 Place the front bumper near the installation position and connect the two connectors of the front bumper assembly harness.放置前保险杠到安装位置附近，连接前保险杠总成线束两个接插件。

8 Place and adjust the front bumper assembly to the installation position, install 4 fixing bolts ① and tighten them.放置并调整前保险杠总成到安装位置，安装4颗固定螺栓①并紧固。 Recommended tools: T30 socket推荐工具：T30套筒

9 Install the 7 fixing screws ① and tighten them.安装7颗固定螺钉①并紧固。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

10 Install a total of 6 fixing screws ① on the left and right and tighten them.安装左右共6颗固定螺钉①并紧固。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

2. Install the right front wheel arch assembly2. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

3. Install the left front wheel arch trim assembly3. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

4. Install the front compartment front upper cover panel assembly4. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

5. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift5. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机