Washing kettle assembly洗涤水壶总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the left front wheel arch assembly2. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

3. Remove the right front wheel arch assembly3. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

4. Remove the front compartment front upper cover panel assembly4. 拆卸机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

5. Remove the front bumper assembly5. 拆卸前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成   Note:提示： ♦  Just remove the front bumper assembly and accessories as a whole without disassembling them.将前保险杠总成及附件整体拆下即可，不必进行拆分。

6. Remove the filling port6. 拆卸加注口 Reference: Filling port参考：加注口

7. Disassemble the washing kettle assembly7. 拆卸洗涤水壶总成

1 Disconnect connector A and disconnect the windshield washer hose assembly I from the washer kettle assembly at B.断开接插件A，从B处断开风窗洗涤软管组件Ⅰ与洗涤水壶总成的连接。 2 Remove 1 fixing nut ② and 2 fixing bolts ①, and remove the washing kettle assembly.拆卸1颗固定螺母②、2颗固定螺栓①，取下洗涤水壶总成。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install the washing kettle assembly1. 安装洗涤水壶总成

1 Place and adjust the washing kettle assembly to the installation position, install 2 fixing bolts ① and 1 fixing nut ② and tighten them.放置并调整洗涤水壶总成到安装位置，安装2颗固定螺栓①、1颗固定螺母②并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 2 Connect the windshield washer hose assembly I and the washer kettle assembly at B, and connect connector A.在B处连接风窗洗涤软管组件Ⅰ与洗涤水壶总成，连接接插件A。

2. Install the filling port2. 安装加注口 Reference: Filling port参考：加注口

3. Install the front bumper assembly3. 安装前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

4. Install the front compartment front upper cover panel assembly4. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

5. Install the right front wheel arch trim assembly5. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

6. Install the left front wheel arch trim assembly6. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

7. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle, and check that the wiper and washing systems should be working normally.7. 降落车辆，连接蓄电池负极，启动车辆，检查雨刮与洗涤系统应正常工作