Front-end module central support bracket assembly前端模块中央支撑支架总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the front compartment front upper cover panel assembly2. 拆卸机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

3. Remove the left front wheel arch assembly3. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

4. Remove the right front wheel arch assembly4. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

5. Remove the front bumper assembly5. 拆卸前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成   Note:提示： ♦  Just remove the front bumper assembly and accessories as a whole without disassembling them.将前保险杠总成及附件整体拆下即可，不必进行拆分。

6. Remove the front bumper center upper bracket assembly6. 拆卸前保险杠中央上支架总成 Reference: Front bumper center upper bracket assembly参考：前保险杠中央上支架总成

7. Remove the front-end module central support bracket assembly7. 拆卸前端模块中央支撑支架总成

1 Pry open all the fixing clips, remove the 4 fixing bolts ①, and remove the front module central support bracket assembly.撬开所有固定卡扣，拆卸4颗固定螺栓①，取下前端模块中央支撑支架总成。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install the front-end module central support bracket assembly1. 安装前端模块中央支撑支架总成

1 Place and adjust the front-end module central support bracket assembly to the installation position, install 4 fixing bolts ① and tighten them, and install all fixing clips.放置并调整前端模块中央支撑支架总成到安装位置，安装4颗固定螺栓①并紧固，安装所有固定卡扣。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m

2. Install the front bumper center upper bracket assembly2. 安装前保险杠中央上支架总成 Reference: Front bumper center upper bracket assembly参考：前保险杠中央上支架总成

3. Install the front bumper assembly3. 安装前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

4. Install right front wheel arch assembly4. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

5. Install the left front wheel arch trim assembly5. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

6. Install the front compartment front upper cover panel assembly6. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

7. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift7. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机