Lower active air intake grille下主动进气格栅

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the upper front guard panel of the front compartment2. 拆卸机舱前上护板 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

3. Remove the left front wheel arch assembly3. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

4. Remove the right front wheel arch assembly4. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

5. Remove the front bumper assembly5. 拆卸前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成   Note:提示： ♦  Just remove the front bumper assembly and accessories as a whole without disassembling them.将前保险杠总成及附件整体拆下即可，不必进行拆分。

6. Remove the front-end module central support bracket assembly6. 拆卸前端模块中央支撑支架总成 Reference: Front-end module central support bracket assembly参考：前端模块中央支撑支架总成

7. Remove the filling port7. 拆卸加注口 Reference: Filling port参考：加注口

8. Disassemble the washing kettle assembly8. 拆卸洗涤水壶总成 Reference: Washing kettle assembly参考：洗涤水壶总成

9. Remove the front anti-collision beam9. 拆卸前防撞梁 Reference: Front anti-collision beam assembly参考：前防撞梁总成

10. Remove the center lower air deflector10. 拆卸中央下部导流板 Reference: Center lower air deflector参考：中央下部导流板

11. Remove the active air intake grille11. 拆卸主动进气格栅

1 Disconnect connector A, pry open the 12 fixing bolts ①, and remove the active air intake grille.断开接插件A，撬开12颗固定螺栓①，取下主动进气格栅。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install active air intake grille1. 安装主动进气格栅

1 Place and adjust the active air intake grille to the installation position, install 12 fixing bolts ①, and connect connector A.放置并调整主动进气格栅到安装位置，安装12颗固定螺栓①，连接接插件A。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m

2. Install the center lower deflector2. 安装中央下部导流板 Reference: Center lower air deflector参考：中央下部导流板

3. Install the front anti-collision beam assembly3. 安装前防撞梁总成 Reference: Front anti-collision beam assembly参考：前防撞梁总成

4. Install the wash kettle assembly4. 安装洗涤水壶总成 Reference: Washing kettle assembly参考：洗涤水壶总成

5. Install the filling port5. 安装加注口 Reference: Filling port参考：加注口

6. Install the front-end module central support bracket assembly6. 安装前端模块中央支撑支架总成 Reference: Front-end module central support bracket assembly参考：前端模块中央支撑支架总成

7. Install the front bumper assembly7. 安装前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

8. Install the right front wheel arch assembly8. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

9. Install the left front wheel arch trim assembly9. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

10. Install the front compartment front upper cover panel assembly10. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

11. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift11. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机