Front-end skeleton前端骨架

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the front compartment front upper cover panel assembly2. 拆卸机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

3. Remove the left front wheel arch assembly3. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

4. Remove the right front wheel arch assembly4. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

5. Remove the front bumper assembly5. 拆卸前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成   Note:提示： ♦  Just remove the front bumper assembly and accessories as a whole without disassembling them.将前保险杠总成及附件整体拆下即可，不必进行拆分。

6. Remove the left front combination lamp6. 拆卸左前组合灯 Reference: Left front combination light参考：左前组合灯

7. Remove the right front combination lamp7. 拆卸右前组合灯 Reference: Right front combination light参考：右前组合灯

8. Remove the front-end module central support bracket assembly8. 拆卸前端模块中央支撑支架总成 Reference: Front-end module central support bracket assembly参考：前端模块中央支撑支架总成

9. Remove the filling port9. 拆卸加注口 Reference: Filling port参考：加注口

10. Disassemble the washing kettle assembly10. 拆卸洗涤水壶总成 Reference: Washing kettle assembly参考：洗涤水壶总成

11. Disassemble the whistle woofer11. 拆卸鸣笛低音喇叭 Reference: Whistling Tweeter参考：鸣笛高音喇叭

12. Remove the whistle tweeter12. 拆卸鸣笛高音喇叭 Reference: Whistling Woofer参考：鸣笛低音喇叭

13. Remove the hood lock assembly13. 拆卸发动机罩锁总成 Reference: Engine hood lock assembly参考：发动机罩锁总成

14. Disassemble the front frame14. 拆卸前端骨架

1 Remove a total of 6 fixing bolts ① and 2 fixing nuts ② on the left and right, and remove the front frame.拆卸左右共6颗固定螺栓①、2颗固定螺母②，取下前端骨架。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install the front-end skeleton1. 安装前端骨架

1 Place and adjust the front frame to the installation position, install a total of 6 fixing bolts ① and 2 fixing nuts ② on the left and right and tighten them.放置并调整前端骨架到安装位置，安装左右共6颗固定螺栓①、2颗固定螺母②并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m①扭矩要求：6-10N•m①

2. Install the left front combination light2. 安装左前组合灯 Reference: Left front combination light参考：左前组合灯

3. Install the right front combination light3. 安装右前组合灯 Reference: Right front combination light参考：右前组合灯

4. Install the wash kettle assembly4. 安装洗涤水壶总成 Reference: Washing kettle assembly参考：洗涤水壶总成

5. Install the filling port5. 安装加注口 Reference: Filling port参考：加注口

6. Install the whistle woofer6. 安装鸣笛低音喇叭 Reference: Whistling Tweeter参考：鸣笛高音喇叭

7. Install the whistle tweeter7. 安装鸣笛高音喇叭 Reference: Whistling Woofer参考：鸣笛低音喇叭

8. Install the hood lock assembly8. 安装发动机罩锁总成 Reference: Engine hood lock assembly参考：发动机罩锁总成

9. Install the front-end module central support bracket assembly9. 安装前端模块中央支撑支架总成 Reference: Front-end module central support bracket assembly参考：前端模块中央支撑支架总成

10. Install the front bumper assembly10. 安装前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

11. Install the right front wheel arch assembly11. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

12. Install the left front wheel arch assembly12. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

13. Install the front compartment front upper cover panel assembly13. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

14. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift14. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机