Hatchback door welded hinge assembly掀背门焊合铰链总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Main mark after disassembly2. 拆卸后主标 Reference: rear main mark参考：后主标

3. Remove liftgate switch3. 拆卸举升门开关 Reference: Liftgate switch参考：举升门开关

4. Disassemble the rear scraper arm scraper assembly4. 拆卸后刮臂刮片总成 Reference: Rear scraper arm scraper assembly参考：后刮臂刮片总成

5. Remove the hatchback door handle box assembly5. 拆卸掀背门拉手盒总成 Reference: Hatchback door handle box assembly参考：掀背门拉手盒总成

6. Remove the hatchback door lower trim panel assembly6. 拆卸掀背门下饰板总成 Reference: Hatchback door lower trim panel assembly参考：掀背门下饰板总成

7. Remove the hatchback door upper trim panel assembly7. 拆卸掀背门上饰板总成 Reference: Hatchback door upper trim panel assembly参考：掀背门上饰板总成

8. Disassemble the rear panoramic parking camera8. 拆卸后全景泊车摄像头 Reference: Rear panoramic parking camera参考：后全景泊车摄像头

9. Remove the rear wiper motor9. 拆卸后刮水器电机 Reference: Rear wiper motor参考：后刮水器电机

10. Remove the trunk opening switch10. 拆卸行李箱开启开关 Reference: Trunk opening switch参考：行李箱开启开关

11. Remove the hatchback door lock assembly11. 拆卸掀背门锁总成 Reference: Hatchback door lock assembly参考：掀背门锁总成

12. Disassemble the hatchback door welded hinge assembly12. 拆卸掀背门焊合铰链总成

1 Disconnect the wiring harness through-hole rubber sleeve from the hatchback door, and disconnect the windshield washer hose assembly A.脱开线束过孔胶套与掀背门的连接，断开风窗洗涤软管组件A。

2 Remove all wire harness clips and fixing points, disconnect the wire harness through-hole rubber sleeve A from the hatchback door, and pull out the wire harness.拆卸所有线束卡扣及固定点，脱开线束过孔胶套A与掀背门的连接，抽出线束。

3 Remove a total of 4 fixing screws ① on both sides, and remove the lower brackets of the electric hatchback door driving parts on both sides.拆卸两侧共4颗固定螺钉①，移开两侧电动掀背门驱动件带下支架。 Recommended tools: T30 socket推荐工具：T30套筒   Caution:注意： ♦  Before removing the liftgate gas spring, lift or support the liftgate welded hinge assembly firmly to avoid personal injury due to its fall.移开掀背门气弹簧前需稳固托举或支撑掀背门焊合铰链总成，避免因其下落导致人员受伤。

4 Remove a total of 4 fixing bolts ① on both sides, and with the help of an assistant, remove the hatchback door welding hinge assembly.拆卸两侧共4颗固定螺栓①，在助手的帮助下，取下掀背门焊合铰链总成。 Recommended tools: 13mm socket推荐工具：13mm套筒   Caution:注意： ♦  The welded hinge assembly of the hatchback door is relatively heavy and needs to be operated by more than two assistants to prevent the hatchback door from falling and causing damage to people or vehicles.掀背门焊合铰链总成较重，需要由两名以上助手协同操作，防止掀背门掉落造成人员或车辆损伤。

Installation procedure安装程序

1. Install hatchback door welding hinge assembly1. 安装掀背门焊合铰链总成

1 Work with an assistant to place and adjust the hatchback door welding hinge assembly to the installation position, install a total of 4 fixing bolts ① on both sides and tighten them.随助手一同放置并调整掀背门焊合铰链总成到安装位置，安装两侧共4颗固定螺栓①并紧固。 Recommended tools: 13mm socket推荐工具：13mm套筒 Torque requirement: 21-27N·m扭矩要求：21-27N•m   Caution:注意： ♦  When placing the hatchback door welding hinge assembly, it is necessary to lift or support the hatchback door welding hinge assembly firmly to avoid personal injury due to its falling.放置掀背门焊合铰链总成时需稳固托举或支撑掀背门焊合铰链总成，避免因其下落导致人员受伤。

2 Place and adjust the lower brackets of the electric hatchback door driving parts on both sides to the installation position, install a total of 4 fixing screws ① on both sides and tighten them.放置并调整两侧电动掀背门驱动件带下支架到安装位置，安装两侧共4颗固定螺钉①并紧固。 Recommended tools: T30 socket推荐工具：T30套筒 Torque requirement: 27-33N·m扭矩要求：27-33N•m   Caution:注意： ♦  Before installing the liftgate gas spring, the liftgate welded hinge assembly must be firmly lifted or supported to avoid personal injury due to its fall.安装掀背门气弹簧前需稳固托举或支撑掀背门焊合铰链总成，避免因其下落导致人员受伤。

3 Insert the wire harness and adjust it to the fixed position, install all wire harness clips and fixing points, and install the through-hole rubber sleeve A to the hatchback door.穿入线束并调整至固定位置，安装所有线束卡扣及固定点，安装过孔胶套A到掀背门。

4 Connect the windshield washer hose assembly A and install the through-hole rubber sleeve to the hatchback door assembly.连接风窗洗涤软管组件A，安装过孔胶套到掀背门总成。

2. Install hatchback door lock assembly2. 安装掀背门锁总成 Reference: Hatchback door lock assembly参考：掀背门锁总成

3. Install the trunk opening switch3. 安装行李箱开启开关 Reference: Trunk opening switch参考：行李箱开启开关

4. Install rear wiper motor4. 安装后刮水器电机 Reference: Rear wiper motor参考：后刮水器电机

5. Install rear panoramic parking camera5. 安装后全景泊车摄像头 Reference: Rear panoramic parking camera参考：后全景泊车摄像头

6. Install the hatchback door upper trim panel assembly6. 安装掀背门上饰板总成 Reference: Hatchback door upper trim panel assembly参考：掀背门上饰板总成

7. Install the hatchback door lower trim panel assembly7. 安装掀背门下饰板总成 Reference: Hatchback door lower trim panel assembly参考：掀背门下饰板总成

8. Install the hatchback door handle box assembly8. 安装掀背门拉手盒总成 Reference: Hatchback door handle box assembly参考：掀背门拉手盒总成

9. Install the rear scraper arm scraper assembly9. 安装后刮臂刮片总成 Reference: Rear scraper arm scraper assembly参考：后刮臂刮片总成

10. Install liftgate switch10. 安装举升门开关 Reference: Liftgate switch参考：举升门开关

11. Main label after installation11. 安装后主标 Reference: rear main mark参考：后主标

12. Connect the negative terminal of the 12V battery and check that the hatchback door opens and closes normally.12. 连接蓄电池负极，检查掀背门开闭应正常工作