Rear bumper module后保险杠模块

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the second row seat cushion assembly2. 拆卸第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

3. Remove the second row left seat back assembly3. 拆卸第二排左座椅靠背总成 Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

4. Remove the second row right seat back assembly4. 拆卸第二排右座椅靠背总成 Reference: Second row right seat back assembly参考：第二排右座椅靠背总成

5. Remove the second row left backrest connection bracket5. 拆卸第二排左靠背连接支架 Reference: Second row left backrest connection bracket参考：第二排左靠背连接支架

6. Remove the second row right backrest connection bracket6. 拆卸第二排右靠背连接支架 Reference: Second row right backrest connection bracket参考：第二排右靠背连接支架

7. Remove the hatchback door sill trim panel assembly7. 拆卸掀背门门槛饰板总成 Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

8. Remove the left rear inner sill trim panel assembly8. 拆卸左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

9. Remove the right rear inner sill trim panel assembly9. 拆卸右后内门槛饰板总成 Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

10. Remove the backup power socket (right C-pillar)10. 拆卸后备电源插座(右C柱) Reference: Backup power socket (right C-pillar)参考：后备电源插座(右C柱)

11. Remove the trunk light11. 拆卸行李箱灯 Reference: luggage compartment light参考：行李箱灯

12. Remove the left C-pillar lower trim panel assembly12. 拆卸左C柱下饰板总成 Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

13. Remove the right C-pillar lower trim panel assembly13. 拆卸右C柱下饰板总成 Reference: Right C-pillar lower trim panel assembly参考：右C柱下饰板总成

14. Remove the left rear combination lamp A14. 拆卸左后组合灯A Reference: Left rear combination lamp A参考：左后组合灯A

15. Remove the right rear combination lamp A15. 拆卸右后组合灯A Reference: Right rear combination lamp A参考：右后组合灯A

16. Disassemble the left rear wheel fender rear section assembly16. 拆卸左后轮眉后段总成 Reference: Left rear wheel fender rear section assembly参考：左后轮眉后段总成

17. Remove the right rear wheel fender rear section assembly17. 拆卸右后轮眉后段总成 Reference: Right rear wheel fender rear section assembly参考：右后轮眉后段总成

18. Remove the rear bumper module18. 拆卸后保险杠模块 1 Disconnect the rear bumper module harness connector.断开后保险杠模块线束接插件。

2 Remove a total of 4 fixing screws ① and 2 fixing bolts ② on the left and right.拆卸左右共4颗固定螺钉①、2颗固定螺栓②。 Recommended tools: Phillips screwdriver, 10mm socket推荐工具：十字螺丝刀、10mm套筒

3 Remove a total of 6 fixing screws on the left and right ①.拆卸左右共6颗固定螺钉①。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

4 Remove the 3 fixing bolts ① and remove the rear bumper module with wiring harness.拆卸3颗固定螺栓①，取下后保险杠模块带线束。 Recommended tools: 10mm socket推荐工具：10mm套筒 5 Remove the rear bumper module from the installation position, disconnect the bumper wire harness through-hole rubber sleeve, disconnect the vehicle interior detection antenna (rear) connector, and remove the rear bumper module.使后保险杠模块脱离安装位置，脱开保险杠线束过孔胶套，断开车内探测天线（后部）接插件，取下后保险杠模块。 6 Disassemble the rear bumper ultrasonic radar assembly.拆卸后保险杠超声波雷达总成。 Reference: Rear bumper ultrasonic radar assembly参考：后保险杠超声波雷达总成 7 After disassembly, protect the millimeter wave radar assembly.拆卸后保毫米波雷达总成。 Reference: Rear protection millimeter wave radar assembly参考：后保毫米波雷达总成 8 Remove the rear fog light.拆卸后雾灯。 Reference: rear fog lights参考：后雾灯

1. Install rear bumper module1. 安装后保险杠模块 1 Install rear fog lights.安装后雾灯。 Reference: rear fog lights参考：后雾灯 2 Protect the millimeter wave radar assembly after installation.安装后保毫米波雷达总成。 Reference: Rear protection millimeter wave radar assembly参考：后保毫米波雷达总成 3 Install the rear bumper ultrasonic radar assembly.安装后保险杠超声波雷达总成。 Reference: Rear bumper ultrasonic radar assembly参考：后保险杠超声波雷达总成 4 Connect the rear connector of the vehicle detection antenna and install the rear bumper module wiring harness through-hole rubber sleeve.连接车内探测天线后部接插件，安装后保险杠模块线束过孔胶套。

5 Place and adjust the rear bumper module to the installation position, install 3 fixing bolts ① and tighten them.放置并调整后保险杠模块到安装位置，安装3颗固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒

6 Install a total of 6 fixing screws ① on the left and right and tighten them.安装左右共6颗固定螺钉①并紧固。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

7 Install a total of 4 fixing screws ① and 2 fixing bolts ② on the left and right and tighten them.安装左右共4颗固定螺钉①、2颗固定螺栓②并紧固。 Recommended tools: Phillips screwdriver, 10mm socket推荐工具：十字螺丝刀、10mm套筒 8 Connect the rear bumper module harness connector.连接后保险杠模块线束接插件。

2. Install the right rear wheel fender rear section assembly2. 安装右后轮眉后段总成 Reference: Right rear wheel fender rear section assembly参考：右后轮眉后段总成

3. Install the left rear wheel fender rear section assembly3. 安装左后轮眉后段总成 Reference: Left rear wheel fender rear section assembly参考：左后轮眉后段总成

4. Install right rear combination light A4. 安装右后组合灯A Reference: Right rear combination lamp A参考：右后组合灯A

5. Install left rear combination lamp A5. 安装左后组合灯A Reference: Left rear combination lamp A参考：左后组合灯A

6. Install the left C-pillar lower trim panel assembly6. 安装左C柱下饰板总成 Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

7. Install the right C-pillar lower trim panel assembly7. 安装右C柱下饰板总成 Reference: Right C-pillar lower trim panel assembly参考：右C柱下饰板总成

8. Install trunk light8. 安装行李箱灯 Reference: luggage compartment light参考：行李箱灯

9. Install the backup power socket (right C-pillar)9. 安装后备电源插座(右C柱) Reference: Backup power socket (right C-pillar)参考：后备电源插座(右C柱)

10. Install the second row left backrest connection bracket10. 安装第二排左靠背连接支架 Reference: Second row left backrest connection bracket参考：第二排左靠背连接支架

11. Install the second row right backrest connection bracket11. 安装第二排右靠背连接支架 Reference: Second row right backrest connection bracket参考：第二排右靠背连接支架

12. Install the left rear inner sill trim panel assembly12. 安装左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

13. Install the right rear inner sill trim panel assembly13. 安装右后内门槛饰板总成 Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

14. Install the second row right seat back assembly14. 安装第二排右座椅靠背总成 Reference: Second row right seat back assembly参考：第二排右座椅靠背总成

15. Install the second row left seat back assembly15. 安装第二排左座椅靠背总成 Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

16. Install the second row seat cushion assembly16. 安装第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

17. Install hatchback door sill trim panel assembly17. 安装掀背门门槛饰板总成 Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

18. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift18. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机