Rear bumper ultrasonic radar assembly后保险杠超声波雷达总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the second row seat cushion assembly2. 拆卸第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

3. Remove the second row left seat back assembly3. 拆卸第二排左座椅靠背总成 Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

4. Remove the second row right seat back assembly4. 拆卸第二排右座椅靠背总成 Reference: Second row right seat back assembly参考：第二排右座椅靠背总成

5. Remove the second row right backrest connection bracket5. 拆卸第二排右靠背连接支架 Reference: Second row right backrest connection bracket参考：第二排右靠背连接支架

6. Remove the backup power socket (auxiliary instrument)6. 拆卸后备电源插座(副仪表) Reference: Backup power socket (auxiliary instrument)参考：后备电源插座(副仪表)

7. Remove the left rear inner sill trim panel assembly7. 拆卸左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

8. Remove the right rear inner sill trim panel assembly8. 拆卸右后内门槛饰板总成 Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

9. Remove the second row left backrest connection bracket9. 拆卸第二排左靠背连接支架 Reference: Second row left backrest connection bracket参考：第二排左靠背连接支架

10. Remove the hatchback door sill trim panel assembly10. 拆卸掀背门门槛饰板总成 Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

11. Remove the trunk light11. 拆卸行李箱灯 Reference: luggage compartment light参考：行李箱灯

12. Remove the left C-pillar lower trim panel assembly12. 拆卸左C柱下饰板总成 Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

13. Remove the right C-pillar lower trim panel assembly13. 拆卸右C柱下饰板总成 Reference: Right C-pillar lower trim panel assembly参考：右C柱下饰板总成

14. Remove the left rear wheel fender rear section assembly14. 拆卸左后轮眉后段总成 Reference: Left rear wheel fender rear section assembly参考：左后轮眉后段总成

15. Remove the right rear wheel fender rear section assembly15. 拆卸右后轮眉后段总成 Reference: Right rear wheel fender rear section assembly参考：右后轮眉后段总成

16. Remove the left rear combination lamp A16. 拆卸左后组合灯A Reference: Left rear combination lamp A参考：左后组合灯A

17. Remove the right rear combination lamp A17. 拆卸右后组合灯A Reference: Right rear combination lamp A参考：右后组合灯A

18. Remove the rear bumper module18. 拆卸后保险杠模块 Reference: Front bumper assembly参考：前保险杠总成

19. Disassemble the rear bumper ultrasonic radar assembly19. 拆卸后保险杠超声波雷达总成

1 Disconnect connector A, pull the tabs on both sides of the rear bumper ultrasonic radar assembly bracket, and remove the rear bumper ultrasonic radar assembly B.断开接插件A，扳动后保险杠超声波雷达总成支架两侧卡舌，取下后保险杠超声波雷达总成B。

Installation procedure安装程序

1. Install the rear bumper ultrasonic radar assembly1. 安装后保险杠超声波雷达总成

1 Place and adjust rear bumper ultrasonic radar assembly B to the installation position, and connect connector A.放置并调整后保险杠超声波雷达总成B到安装位置，连接接插件A。

2. Install the rear bumper assembly2. 安装后保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

3. Install right rear combination lamp A3. 安装右后组合灯A Reference: Right rear combination lamp A参考：右后组合灯A

4. Install left rear combination light A4. 安装左后组合灯A Reference: Left rear combination lamp A参考：左后组合灯A

5. Install the right rear wheel fender rear section assembly5. 安装右后轮眉后段总成 Reference: Right rear wheel fender rear section assembly参考：右后轮眉后段总成

6. Install the left rear wheel fender rear section assembly6. 安装左后轮眉后段总成 Reference: Left rear wheel fender rear section assembly参考：左后轮眉后段总成

7. Install the right C-pillar lower trim panel assembly7. 安装右C柱下饰板总成 Reference: Right C-pillar lower trim panel assembly参考：右C柱下饰板总成

8. Install the left C-pillar lower trim panel assembly8. 安装左C柱下饰板总成 Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

9. Install trunk light9. 安装行李箱灯 Reference: luggage compartment light参考：行李箱灯

10. Install hatchback door sill trim panel assembly10. 安装掀背门门槛饰板总成 Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

11. Install the second row left backrest connection bracket11. 安装第二排左靠背连接支架 Reference: Second row left backrest connection bracket参考：第二排左靠背连接支架

12. Install the right rear inner sill trim panel assembly12. 安装右后内门槛饰板总成 Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

13. Install the left rear inner sill trim panel assembly13. 安装左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

14. Install the backup power socket (auxiliary instrument)14. 安装后备电源插座(副仪表) Reference: Backup power socket (auxiliary instrument)参考：后备电源插座(副仪表)

15. Install the second row right backrest connection bracket15. 安装第二排右靠背连接支架 Reference: Second row right backrest connection bracket参考：第二排右靠背连接支架

16. Install the second row right seat back assembly16. 安装第二排右座椅靠背总成 Reference: Second row right seat back assembly参考：第二排右座椅靠背总成

17. Install the second row left seat back assembly17. 安装第二排左座椅靠背总成 Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

18. Install the second row seat cushion assembly18. 安装第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

19. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift. Check that the rear bumper ultrasonic radar assembly should work normally.19. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，检查后保险杠超声波雷达总成应正常工作