Front left seat assembly前排左座椅总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road and activate the parking brake.将车辆停在平坦路面，启用驻车制动。

2. Remove the front left seat assembly2. 拆卸前排左座椅总成

1 Remove the 2 fixing bolts ①.拆卸2颗固定螺栓①。 Recommended tools: T50 socket推荐工具：T50套筒   Note:提示： ♦  Turn the vehicle's power supply to "ON" and adjust the electric seat forward until the rear fixing bolts are exposed.使车辆电源状态为“ON”，将电动座椅向前调节至露出后方固定螺栓。

2 Remove the 2 fixing bolts ① to disengage the front left seat assembly A from the installation position.拆卸2颗固定螺栓①，使前排左座椅总成A脱离安装位置。 Recommended tools: T50 socket推荐工具：T50套筒   Note:提示： ♦  Turn the vehicle's power supply to "ON" and adjust the electric seat backward until the front fixing bolts are exposed.使车辆电源状态为“ON”，将电动座椅向后调节至露出前方固定螺栓。 3 Put the vehicle power supply in "OFF" state and disconnect the negative terminal of the 12V battery.使整车电源处于“OFF”状态，断开蓄电池负极。 4 Disconnect the left seat assembly connector and remove the wiring harness fixing card.断开左座椅总成接插件，拆卸线束固定卡。 Recommended tools: clip remover推荐工具：卡扣起子   Caution:注意： ♦  Disconnect the negative terminal of the 12V battery for 90 seconds before disconnecting the seat airbag connector.断开蓄电池负极90s后，方可断开座椅气囊接插件。 5 Take out the front left seat assembly at a suitable angle.以合适的角度取出前排左座椅总成。   Caution:注意： ♦  When taking out the front seat assembly, be careful not to scratch or damage the interior trim parts with sharp parts such as seat slide rails.取出前排座椅总成时谨防座椅滑轨等尖锐部件划伤或损坏车内饰件。

Installation procedure安装程序

1. Install the front left seat assembly1. 安装前排左座椅总成 1 Connect the connector to the front left seat assembly and install the wire harness fixing clip.连接接插件到前排左座椅总成，安装线束固定卡扣。 2 Connect the negative terminal of the 12V battery.连接蓄电池负极。

3 Place and adjust the front left seat assembly A to the installation position, install 2 fixing bolts ① and tighten them.放置并调整前排左座椅总成A到安装位置，安装2颗固定螺栓①并紧固。 Recommended tools: T50 socket推荐工具：T50套筒 Torque requirement: 40–50N·m扭矩要求：40–50N•m   Note:提示： ♦  Turn the vehicle's power supply to "ON" and adjust the electric seat backward until the front fixing bolts are exposed.使车辆电源状态为“ON”，将电动座椅向后调节至露出前方固定螺栓。

4 Install the 2 fixing bolts ① and tighten them.安装2颗固定螺栓①并紧固。 Recommended tools: T50 socket推荐工具：T50套筒 Torque requirement: 40–50N·m扭矩要求：40–50N•m   Note:提示： ♦  Turn the vehicle's power supply to "ON" and adjust the electric seat forward until the rear fixing bolts are exposed.使车辆电源状态为“ON”，将电动座椅向前调节至露出后方固定螺栓。

2. Check that the seat adjustment should work properly2. 检查座椅调节应正常工作