Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Park the vehicle on a flat road, activate the parking brake, and turn the vehicle power supply to "OFF".将车辆停在平坦路面，启用驻车制动，整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
|
|
|
2. Remove the driver's side lower left decorative panel assembly2. 拆卸驾驶侧左下装饰板总成
|
|
|
3. Remove the driver’s side lower cover panel assembly3. 拆卸驾驶侧下护板总成
|
|
|
4. Remove the left end cover assembly of the instrument panel4. 拆卸仪表板左侧端盖总成
|
|
|
5. Remove the left end cover of the instrument panel5. 拆卸仪表板左侧端盖盖板
|
|
|
6. Remove the left front inner sill trim panel assembly6. 拆卸左前内门槛饰板总成
|
|
|
7. Remove the second row seat cushion assembly7. 拆卸第二排座椅坐垫总成
|
|
|
8. Remove the left rear inner sill trim panel assembly8. 拆卸左后内门槛饰板总成
|
|
|
9. Remove the left B-pillar air outlet assembly9. 拆卸左侧B柱出风口总成
|
|
|
10. Remove the left B-pillar lower trim panel assembly10. 拆卸左B柱下饰板总成
|
|
|
11. Remove the left B-pillar upper trim panel assembly11. 拆卸左B柱上饰板总成
|
|
|
12. Remove the left B-pillar air duct assembly12. 拆卸左侧B柱风管总成
|
|
|
13. Remove the first row left seat belt assembly13. 拆卸第一排左侧安全带总成
|
|
|
1 Remove the 2 fixing bolts ① and remove the left side guide bracket A of the front seat belt.拆卸2颗固定螺栓①，取下前排安全带左侧导向支架A。
|
|
Recommended tools: 8mm socket推荐工具：8mm套筒 |
|
|
|
2 Remove the fixing bolt ①.拆卸固定螺栓①。
|
|
Recommended tools: 17mm socket推荐工具：17mm套筒 |
3 Disconnect the seat belt connector.断开安全带接插件。
|
|
|
4 Remove the fixing bolts ① and ②, and take out the first row left seat belt assembly A.拆卸固定螺栓①、固定螺栓②，取出第一排左侧安全带总成A。
|
|
Recommended tools: 10mm socket ①, 17mm socket ②推荐工具：10mm套筒①、17mm套筒② |
|
Installation procedure安装程序
|
|
1. Install the first row left seat belt assembly1. 安装第一排左侧安全带总成
|
|
|
1 Place and adjust the first row left seat belt assembly A to the installation position, install the fixing bolt ② and the fixing bolt ① and tighten them.放置并调整第一排左侧安全带总成A到安装位置，安装固定螺栓②、固定螺栓①并紧固。
|
|
Recommended tools: 10mm socket ①, 17mm socket ②推荐工具：10mm套筒①、17mm套筒② |
|
|
Torque requirements: 7-9N·m①, 50-60N·m②扭矩要求：7-9N•m①、50-60N•m② |
2 Connect the seat belt connector.连接安全带接插件。
|
|
|
3 Install the fixing bolts ① and tighten them.安装固定螺栓①并紧固。
|
|
Recommended tools: 17mm socket推荐工具：17mm套筒 |
|
|
Torque requirement: 50-60N·m扭矩要求：50-60N•m |
|
|
|
4 Install the left side guide bracket A of the front seat belt to the installation position, install 2 fixing bolts ① and tighten them.安装前排安全带左侧导向支架A到安装位置，安装2颗固定螺栓①并紧固。
|
|
Recommended tools: 8mm socket推荐工具：8mm套筒 |
|
|
Torque requirement: 7-9N·m扭矩要求：7-9N•m |
|
|
|
2. Install the left B-pillar air duct assembly2. 安装左侧B柱风管总成
|
|
|
3. Install the left B-pillar upper trim panel assembly3. 安装左B柱上饰板总成
|
|
|
4. Install the left B-pillar air vent assembly.4. 安装左侧B柱出风口总成
|
|
|
5. Install the left B-pillar lower trim panel assembly5. 安装左B柱下饰板总成
|
|
|
6. Install the left rear inner sill trim panel assembly6. 安装左后内门槛饰板总成
|
|
|
7. Install the second row seat cushion assembly7. 安装第二排座椅坐垫总成
|
|
|
8. Install the left front inner sill trim panel assembly8. 安装左前内门槛饰板总成
|
|
|
9. Install the left end cover of the instrument panel9. 安装仪表板左侧端盖盖板
|
|
|
10. Install the left end cover assembly of the instrument panel10. 安装仪表板左侧端盖总成
|
|
|
11. Install the driver’s side lower cover panel assembly11. 安装驾驶侧下护板总成
|
|
|
12. Install the driver's side lower left decorative panel assembly12. 安装驾驶侧左下装饰板总成
|
|
|
13. Connect the negative terminal of the 12V battery and check that the left seat belt assembly of the first row should work normally.13. 连接蓄电池负极，检查第一排左侧安全带总成应正常工作
|
First row left seat belt assembly第一排左侧安全带总成
