Rear bumper upper left mounting bracket assembly后保险杠左上安装支架总成

Removal procedure拆卸程序

1. Preparation1. 准备工作

1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，使整车电源处于“OFF”状态。

2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

3 Lift the vehicle.举升车辆。

2. Remove the second row seat cushion assembly2. 拆卸第二排座椅坐垫总成

Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

3. Remove the second row left seat back assembly3. 拆卸第二排左座椅靠背总成

Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

4. Remove the second row right seat back assembly4. 拆卸第二排右座椅靠背总成

Reference: Second row right seat back assembly参考：第二排右座椅靠背总成

5. Remove the second row left backrest connection bracket5. 拆卸第二排左靠背连接支架

Reference: Second row left backrest connection bracket参考：第二排左靠背连接支架

6. Remove the second row right backrest connection bracket6. 拆卸第二排右靠背连接支架

Reference: Second row right backrest connection bracket参考：第二排右靠背连接支架

7. Remove the hatchback door sill trim panel assembly7. 拆卸掀背门门槛饰板总成

Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

8. Remove the left rear inner sill trim panel assembly8. 拆卸左后内门槛饰板总成

Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

9. Remove the right rear inner sill trim panel assembly9. 拆卸右后内门槛饰板总成

Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

10. Remove the backup power socket (right C-pillar)10. 拆卸后备电源插座(右C柱)

Reference: Backup power socket (right C-pillar)参考：后备电源插座(右C柱)

11. Remove the trunk light11. 拆卸行李箱灯

Reference: luggage compartment light参考：行李箱灯

12. Remove the left C-pillar lower trim panel assembly12. 拆卸左C柱下饰板总成

Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

13. Remove the right C-pillar lower trim panel assembly13. 拆卸右C柱下饰板总成

Reference: Right C-pillar lower trim panel assembly参考：右C柱下饰板总成

14. Remove the left rear combination lamp A14. 拆卸左后组合灯A

Reference: Left rear combination lamp A参考：左后组合灯A

15. Remove the right rear combination lamp A15. 拆卸右后组合灯A

Reference: Right rear combination lamp A参考：右后组合灯A

16. Disassemble the left rear wheel fender rear section assembly16. 拆卸左后轮眉后段总成

Reference: Left rear wheel fender rear section assembly参考：左后轮眉后段总成

17. Remove the right rear wheel fender rear section assembly17. 拆卸右后轮眉后段总成

Reference: Right rear wheel fender rear section assembly参考：右后轮眉后段总成

18. Remove the rear bumper module18. 拆卸后保险杠模块

Reference: Rear bumper module参考：后保险杠模块

Note:提示：

♦

Just remove the rear bumper module and accessories as a whole, no need to disassemble them.将后保险杠模块及附件整体拆下即可，不必进行拆分。

19. Remove the rear bumper upper left mounting bracket assembly19. 拆卸后保险杠左上安装支架总成

1 Remove the 5 fixing screws ① and remove the upper left mounting bracket assembly of the rear bumper.拆卸5颗固定螺钉①，取下后保险杠左上安装支架总成。

Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

Installation procedure安装程序

1. Install the upper left rear bumper mounting bracket assembly1. 安装后保险杠左上安装支架总成

1 Place and adjust the upper left rear bumper mounting bracket assembly to the installation position, install 5 fixing screws ① and tighten.放置并调整后保险杠左上安装支架总成到安装位置，安装5颗固定螺钉①并紧固。

Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀