Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，使整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
3 Lift the vehicle.举升车辆。
|
|
|
2. Remove the front compartment front lower cover panel assembly2. 拆卸机舱前下护板总成
|
|
|
3. Drain the coolant from the temperature control system3. 排放温控系统冷却液
|
|
|
4. Remove the front right seat assembly4. 拆卸前排右座椅总成
|
|
|
5. Remove the second row seat cushion assembly5. 拆卸第二排座椅坐垫总成
|
|
|
6. Remove the right rear inner sill trim panel assembly6. 拆卸右后内门槛饰板总成
|
|
|
7. Remove the lower right decorative panel assembly on the passenger side7. 拆卸副驾驶侧右下装饰板总成
|
|
|
8. Remove the right end cover assembly of the instrument panel8. 拆卸仪表板右侧端盖总成
|
|
|
9. Remove the right end cover of the instrument panel9. 拆卸仪表板右侧端盖盖板
|
|
|
10. Remove the right front inner sill trim panel assembly10. 拆卸右前内门槛饰板总成
|
|
|
11. Remove the right B-pillar lower trim panel assembly11. 拆卸右B柱下饰板总成
|
|
|
12. Remove the driver's side lower left decorative panel assembly12. 拆卸驾驶侧左下装饰板总成
|
|
|
13. Remove the driver’s side lower cover panel assembly13. 拆卸驾驶侧下护板总成
|
|
|
14. Remove the left front extension plate assembly14. 拆卸左前延伸板总成
|
|
|
15. Remove the right front extension plate assembly15. 拆卸右前延伸板总成
|
|
|
16. Remove the switch panel assembly16. 拆卸开关面板总成
|
|
|
17. Remove the sub-instrument panel body assembly17. 拆卸副仪表板本体总成
|
|
|
18. Remove ITS to charger water pipe II18. 拆卸ITS至充电机水管Ⅱ
1 Lift up the right front part of the passenger compartment carpet assembly.掀起乘客舱地毯总成右侧前方部位。
|
|
|
2 Disconnect the water pipe joints A and B from the ITS to the charger water pipe II.断开ITS至充电机水管Ⅱ的水管接头A、B。
|
|
|
3 Remove the fixing bolt ①.拆卸固定螺栓①。
|
|
Recommended tools: 10mm socket推荐工具：10mm套筒 |
|
|
|
4 Remove the fixing bolt ①.拆卸固定螺栓①。
|
|
Recommended tools: 10mm socket推荐工具：10mm套筒 |
|
|
|
5 Disconnect ITS to charger water pipe I connectors A and B.断开ITS至充电机水管Ⅰ接头A、B。
|
|
|
6 Remove the 2 fixing nuts ① and remove the ITS to the charger water pipe Ⅱ.拆卸2颗固定螺母①，取下ITS至充电机水管Ⅱ。
|
|
Recommended tools: 10mm socket推荐工具：10mm套筒 |
|
Installation procedure安装程序
|
|
1. Install ITS to charger water pipe II1. 安装ITS至充电机水管Ⅱ
|
|
|
1 Place and adjust the ITS to the charger water pipe Ⅱ to the installation position, install 2 fixing nuts ① and tighten them.放置并调整ITS至充电机水管Ⅱ到安装位置，安装2颗固定螺母①并紧固。
|
|
Recommended tools: 10mm socket推荐工具：10mm套筒 |
|
|
Torque requirement: 6-10N·m扭矩要求：6-10N•m |
|
|
|
2 Connect ITS to charger water pipe I connectors A and B.连接ITS至充电机水管Ⅰ接头A、B。
|
|
|
3 Install the fixing bolts ① and tighten them.安装固定螺栓①并紧固。
|
|
Recommended tools: 10mm socket推荐工具：10mm套筒 |
|
|
Torque requirement: 6-10N·m扭矩要求：6-10N•m |
|
|
|
4 Install the fixing bolts ① and tighten them.安装固定螺栓①并紧固。
|
|
Recommended tools: 10mm socket推荐工具：10mm套筒 |
|
|
Torque requirement: 6-10N·m扭矩要求：6-10N•m |
|
|
|
5 Connect the ITS to the water pipe joints A and B of the charger water pipe II.连接ITS至充电机水管Ⅱ的水管接头A、B。
6 Reset the right front part of the passenger compartment carpet assembly.复位乘客舱地毯总成右侧前方部位。
|
|
|
2. Install the sub-instrument panel body assembly2. 安装副仪表板本体总成
|
|
|
3. Install the right B-pillar lower trim panel assembly3. 安装右B柱下饰板总成
|
|
|
4. Install the right rear inner door sill trim assembly4. 安装右后内门槛饰板总成
|
|
|
5. Install the second row seat cushion assembly5. 安装第二排座椅坐垫总成
|
|
|
6. Install switch panel assembly6. 安装开关面板总成
|
|
|
7. Install the right front extension plate assembly7. 安装右前延伸板总成
|
|
|
8. Install the left front extension plate assembly8. 安装左前延伸板总成
|
|
|
9. Install the driver’s side lower cover panel assembly9. 安装驾驶侧下护板总成
|
|
|
10. Install the driver's side lower left decorative panel assembly10. 安装驾驶侧左下装饰板总成
|
|
|
11. Install the front left seat assembly11. 安装前排左座椅总成
|
|
|
12. Install the right front inner sill trim panel assembly12. 安装右前内门槛饰板总成
|
|
|
13. Install the right end cover of the instrument panel13. 安装仪表板右侧端盖盖板
|
|
|
14. Install the right end cover assembly of the instrument panel14. 安装仪表板右侧端盖总成
|
|
|
15. Install the passenger side lower right decorative panel assembly15. 安装副驾驶侧右下装饰板总成
|
|
|
16. Fill the temperature control system coolant16. 加注温控系统冷却液
|
|
|
17. Install the front compartment front lower cover panel assembly17. 安装机舱前下护板总成
|
|
|
18. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, check that the cooling system should be working normally18. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，检查冷却系统应正常工作
|
ITS to charger water pipe ⅡITS至充电机水管Ⅱ
