In-car detection antenna (rear)车内探测天线(后部)

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the second row seat cushion assembly2. 拆卸第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

3. Remove the second row left seat back assembly3. 拆卸第二排左座椅靠背总成 Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

4. Remove the second row right seat back assembly4. 拆卸第二排右座椅靠背总成 Reference: Second row right seat back assembly参考：第二排右座椅靠背总成

5. Remove the second row left backrest connection bracket5. 拆卸第二排左靠背连接支架 Reference: Second row left backrest connection bracket参考：第二排左靠背连接支架

6. Remove the second row right backrest connection bracket6. 拆卸第二排右靠背连接支架 Reference: Second row right backrest connection bracket参考：第二排右靠背连接支架

7. Remove the hatchback door sill trim panel assembly7. 拆卸掀背门门槛饰板总成 Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

8. Remove the left rear inner sill trim panel assembly8. 拆卸左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

9. Remove the right rear inner sill trim panel assembly9. 拆卸右后内门槛饰板总成 Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

10. Remove the backup power socket (right C-pillar)10. 拆卸后备电源插座(右C柱) Reference: Backup power socket (right C-pillar)参考：后备电源插座(右C柱)

11. Remove the trunk light11. 拆卸行李箱灯 Reference: luggage compartment light参考：行李箱灯

12. Remove the left C-pillar lower trim panel assembly12. 拆卸左C柱下饰板总成 Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

13. Remove the right C-pillar lower trim panel assembly13. 拆卸右C柱下饰板总成 Reference: Right C-pillar lower trim panel assembly参考：右C柱下饰板总成

14. Remove the left rear combination lamp A14. 拆卸左后组合灯A Reference: Left rear combination lamp A参考：左后组合灯A

15. Remove the right rear combination lamp A15. 拆卸右后组合灯A Reference: Right rear combination lamp A参考：右后组合灯A

16. Disassemble the left rear wheel fender rear section assembly16. 拆卸左后轮眉后段总成 Reference: Left rear wheel fender rear section assembly参考：左后轮眉后段总成

17. Remove the right rear wheel fender rear section assembly17. 拆卸右后轮眉后段总成 Reference: Right rear wheel fender rear section assembly参考：右后轮眉后段总成

18. Remove the rear bumper module18. 拆卸后保险杠模块 Reference: Rear bumper module参考：后保险杠模块   Note:提示： ♦  Just remove the rear bumper module and accessories as a whole, no need to disassemble them.将后保险杠模块及附件整体拆下即可，不必进行拆分。

19. Remove the detection antenna in the car19. 拆卸车内探测天线

1 Remove the 2 fixing bolts ① and remove the detection antenna in the car.拆卸2颗固定螺栓①，取下车内探测天线。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install the in-car detection antenna1. 安装车内探测天线

1 Place and adjust the vehicle detection antenna to the installation position, install 2 fixing bolts ① and tighten them.放置并调整车内探测天线到安装位置，安装2颗固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m

2. Install the rear bumper module2. 安装后保险杠模块 Reference: Rear bumper module参考：后保险杠模块

3. Install the right rear wheel fender rear section assembly3. 安装右后轮眉后段总成 Reference: Right rear wheel fender rear section assembly参考：右后轮眉后段总成

4. Install the rear section of the left rear wheel arch assembly.4. 安装左后轮眉后段总成 Reference: Left rear wheel fender rear section assembly参考：左后轮眉后段总成

5. Install right rear combination lamp A5. 安装右后组合灯A Reference: Right rear combination lamp A参考：右后组合灯A

6. Install left rear combination lamp A6. 安装左后组合灯A Reference: Left rear combination lamp A参考：左后组合灯A

7. Install the left C-pillar lower trim panel assembly7. 安装左C柱下饰板总成 Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

8. Install the right C-pillar lower trim panel assembly8. 安装右C柱下饰板总成 Reference: Right C-pillar lower trim panel assembly参考：右C柱下饰板总成

9. Install trunk light9. 安装行李箱灯 Reference: luggage compartment light参考：行李箱灯

10. Install the backup power socket (right C-pillar)10. 安装后备电源插座(右C柱) Reference: Backup power socket (right C-pillar)参考：后备电源插座(右C柱)

11. Install the second row left backrest connection bracket11. 安装第二排左靠背连接支架 Reference: Second row left backrest connection bracket参考：第二排左靠背连接支架

12. Install the second row right backrest connection bracket12. 安装第二排右靠背连接支架 Reference: Second row right backrest connection bracket参考：第二排右靠背连接支架

13. Install the left rear inner sill trim panel assembly13. 安装左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

14. Install the right rear inner sill trim panel assembly14. 安装右后内门槛饰板总成 Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

15. Install the second row right seat back assembly15. 安装第二排右座椅靠背总成 Reference: Second row right seat back assembly参考：第二排右座椅靠背总成

16. Install the second row left seat back assembly16. 安装第二排左座椅靠背总成 Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

17. Install the second row seat cushion assembly17. 安装第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

18. Install hatchback door sill trim panel assembly18. 安装掀背门门槛饰板总成 Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

19. Connect the negative terminal of the 12V battery, start the vehicle, and check that the keyless entry system should work normally.19. 连接蓄电池负极，启动车辆，检查无钥匙进入系统应正常工作