Left suspension assembly左悬置总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the front compartment front lower cover panel assembly2. 拆卸机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

3. Remove the left front wheel arch assembly3. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

4. Remove the left front wheel assembly4. 拆卸左前车轮总成 Reference: Wheel assembly参考：车轮总成

5. Remove the left front wheel fender assembly5. 拆卸左前轮挡泥板总成 Reference: Left front wheel fender assembly参考：左前轮挡泥板总成

6. Disassemble the air conditioning compressor assembly6. 拆卸空调压缩机总成 Reference: Air conditioning compressor assembly参考：空调压缩机总成

7. Remove the left suspension assembly7. 拆卸左悬置总成 1 Use hydraulic brackets to securely support the integrated electric drive assembly.使用液压托架稳固支撑集成电力驱动总成。 Recommended tools: Hydraulic bracket推荐工具：液压托架

2 Remove 4 fixing bolts ①, 1 fixing nut and bolt ②, and remove the left suspension assembly.拆卸4颗固定螺栓①、1颗固定螺母及螺栓②，取下左悬置总成。 Recommended tools: 18mm socket推荐工具：18mm套筒   Warning:警告： ♦  Care should be taken when disassembling, and attention should be paid to the support of the integrated electric drive assembly. If there is slippage, adjustments should be made in time to avoid safety accidents.拆卸时应谨慎操作，注意集成电力驱动总成支撑情况，若有滑脱应及时调整，避免发生安全事故。

Installation procedure安装程序

1. Install the left suspension assembly1. 安装左悬置总成

1 Place and adjust the left suspension assembly to the installation position, install 4 fixing bolts ①, 1 fixing bolt and nut ② and tighten them.放置并调整左悬置总成到安装位置，安装4颗固定螺栓①、1颗固定螺栓及螺母②并紧固。 Recommended tools: 18mm socket推荐工具：18mm套筒 Torque requirement: 110-130N·m扭矩要求：110-130N•m   Warning:警告： ♦  Caution should be exercised during installation, and attention should be paid to the support of the integrated electric drive assembly. If there is slippage, adjustments should be made in time to avoid safety accidents.安装时应谨慎操作，注意集成电力驱动总成支撑情况，若有滑脱应及时调整，避免发生安全事故。 2 Slowly lower the hydraulic bracket and remove it.缓慢降落液压托架并移出。 Recommended tools: Hydraulic bracket推荐工具：液压托架

2. Install air conditioning compressor assembly2. 安装空调压缩机总成 Reference: Air conditioning compressor assembly参考：空调压缩机总成

3. Install the left front wheel fender assembly3. 安装左前轮挡泥板总成 Reference: Left front wheel fender assembly参考：左前轮挡泥板总成

4. Install the left front wheel assembly4. 安装左前车轮总成 Reference: Wheel assembly参考：车轮总成

5. Install the left front wheel arch trim assembly5. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

6. Install the front compartment front lower cover panel assembly6. 安装机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

7. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, conduct a road test and check7. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，路试检查