Thermal Management Integrated Module Bracket I热管理集成模块支架Ⅰ

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the front compartment front lower cover panel assembly2. 拆卸机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

3. Recycle refrigerant3. 回收制冷剂 Reference: Recycling and recharging refrigerant参考：回收和加注制冷剂

4. Drain the temperature control system coolant4. 排放温控系统冷却液 Reference: Temperature control system coolant参考：温控系统冷却液

5. Remove the front compartment front upper cover panel assembly5. 拆卸机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

6. Remove the left front wheel arch assembly6. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

7. Remove the right front wheel arch assembly7. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

8. Remove the front bumper assembly8. 拆卸前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

9. Remove the thermal management integrated module9. 拆卸热管理集成模块 Reference: Thermal Management Integrated Module参考：热管理集成模块

10. Remove the thermal management integrated module bracket Ⅰ10. 拆卸热管理集成模块支架Ⅰ

1 Remove the 2 fixing nuts ① and remove the thermal management integrated module bracket ⅠA.拆卸2颗固定螺母①，取下热管理集成模块支架ⅠA。 Recommended tools: 13mm socket推荐工具：13mm套筒

Installation procedure安装程序

1. Install the thermal management integrated module bracket Ⅰ1. 安装热管理集成模块支架Ⅰ

1 Place and adjust the thermal management integrated module bracket IA to the installation position, install 2 fixing nuts ① and tighten them.放置并调整热管理集成模块支架ⅠA到安装位置，安装2颗固定螺母①并紧固。 Recommended tools: 13mm socket推荐工具：13mm套筒 Torque requirement: 20-24N·m扭矩要求：20-24N•m

2. Install the thermal management integrated module2. 安装热管理集成模块 Reference: Thermal Management Integrated Module参考：热管理集成模块

3. Fill the temperature control system coolant3. 加注温控系统冷却液 Reference: Temperature control system coolant参考：温控系统冷却液

4. Install front bumper assembly4. 安装前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

5. Install the left front wheel arch trim assembly5. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

6. Install the right front wheel arch trim assembly6. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

7. Install the front compartment front upper cover panel assembly7. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

8. Add refrigerant8. 加注制冷剂 Reference: Recycling and recharging refrigerant参考：回收和加注制冷剂

9. Install the front compartment front lower cover panel assembly9. 安装机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

10. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, check that the thermal management integrated module should work normally10. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，检查热管理集成模块应正常工作