Thermal Management Integrated Module热管理集成模块

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Recycle refrigerant2. 回收制冷剂 Reference: Recycling and recharging refrigerant参考：回收和加注制冷剂

3. Remove the front compartment front lower cover panel assembly3. 拆卸机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

4. Drain the temperature control system coolant4. 排放温控系统冷却液 Reference: Temperature control system coolant参考：温控系统冷却液

5. Remove the front compartment front upper cover panel assembly5. 拆卸机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

6. Remove the left front wheel arch assembly6. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

7. Remove the right front wheel arch assembly7. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

8. Remove the front bumper assembly8. 拆卸前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

9. Remove the thermal management integrated module9. 拆卸热管理集成模块 1 Disconnect the two connectors connecting the front compartment wiring harness to the thermal management integrated module.断开前舱线束与热管理集成模块连接的两个接插件。

2 Disconnect water pipe joints A, B, C, D, E, and F from the thermal management integrated module.断开水管接头A、B、C、D、E、F与热管理集成模块的连接。

3 Disconnect water pipe connectors A, B, and C.断开水管接头A、B、C。

4 Remove the 6 fixing bolts ① and disconnect all air conditioning pipelines from the thermal management integrated module.拆卸6颗固定螺栓①，断开所有空调管路与热管理集成模块的连接。 Recommended tools: 10mm socket推荐工具：10mm套筒

5 Remove a total of 4 fixing bolts on the left and right ①.拆卸左右共4颗固定螺栓①。 Recommended tools: 13mm socket推荐工具：13mm套筒

Installation procedure安装程序

1. Install the thermal management integrated module1. 安装热管理集成模块

1 Place and adjust the thermal management integrated module to the installation position, install a total of 4 fixing bolts on the left and right ① and tighten them.放置并调整热管理集成模块到安装位置，安装左右共4颗固定螺栓①并紧固。 Recommended tools: 13mm socket推荐工具：13mm套筒 Torque requirement: 22-28N·m扭矩要求：22-28N•m

2 Install all air conditioning pipe joints to the installation position, install 6 fixing bolts ① and tighten them.安装所有空调管路接头到安装位置，安装6颗固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m   Caution:注意： ♦  The O-ring of the air conditioning pipeline is a disposable part, please use new parts for each installation.空调管路O型圈为一次性部件，每次安装请使用新件。

3 Connect water pipe connectors A, B, and C to the thermal management integrated module.连接水管接头A、B、C到热管理集成模块。

4 Connect the water pipe connectors A, B, C, D, E, and F to the thermal management integrated module.连接水管接头A、B、C、D、E、F到热管理集成模块。 5 Connect the two connectors between the front compartment wiring harness and the thermal management integrated module.连接前舱线束与热管理集成模块连接的两个接插件。

2. Fill the temperature control system coolant2. 加注温控系统冷却液 Reference: Temperature control system coolant参考：温控系统冷却液

3. Install the front compartment front lower cover panel assembly3. 安装机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

4. Install front bumper assembly4. 安装前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

5. Install the left front wheel arch trim assembly5. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

6. Install the right front wheel arch trim assembly6. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

7. Install the front compartment front upper cover panel assembly7. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

8. Add refrigerant8. 加注制冷剂 Reference: Recycling and recharging refrigerant参考：回收和加注制冷剂

9. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, check that the thermal management integrated module should work normally9. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，检查热管理集成模块应正常工作