B-pillar side impact sensorB柱侧碰传感器

Note:提示： ♦  The disassembly and assembly procedures for the left and right B-pillar side impact sensors are basically the same. The following content takes the left side as an example.左、右B柱侧碰传感器的拆装程序基本相同，下述内容以左侧为例进行操作。

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and turn the vehicle power supply to "OFF".将车辆停在平坦路面，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove the driver's side lower left decorative panel assembly2. 拆卸驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

3. Remove the driver’s side lower cover panel assembly3. 拆卸驾驶侧下护板总成 Reference: Driver's side lower cover panel assembly参考：驾驶侧下护板总成

4. Remove the left end cover assembly of the instrument panel4. 拆卸仪表板左侧端盖总成 Reference: Instrument panel left end cover assembly参考：仪表板左侧端盖总成

5. Remove the left end cover of the instrument panel5. 拆卸仪表板左侧端盖盖板 Reference: Instrument panel left end cover参考：仪表板左侧端盖盖板

6. Remove the left front inner sill trim panel assembly6. 拆卸左前内门槛饰板总成 Reference: Left front inner sill trim panel assembly参考：左前内门槛饰板总成

7. Remove the second row seat cushion assembly7. 拆卸第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

8. Remove the left rear inner sill trim panel assembly8. 拆卸左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

9. Remove the left B-pillar air outlet assembly9. 拆卸左侧B柱出风口总成 Reference: Left B-pillar air duct assembly参考：左侧B柱风管总成

10. Remove the left B-pillar lower trim panel assembly10. 拆卸左B柱下饰板总成 Reference: Left B-pillar lower trim panel assembly参考：左B柱下饰板总成

11. Remove the B-pillar side impact sensor11. 拆卸B柱侧碰传感器

1 Disconnect connector A.断开接插件A。   Warning:警告： ♦  Disconnect the negative terminal of the 12V battery for 90 seconds before operating the airbag system.断开蓄电池负极90s后，方可对安全气囊系统进行操作。

2 Remove the fixing bolt ① and remove the B-pillar side impact sensor A.拆卸固定螺栓①，取下B柱侧碰传感器A。 Recommended tools: 8mm socket推荐工具：8mm套筒   Caution:注意： ♦  After removing the B-pillar side impact sensor, avoid falling or bumping it and keep it clean.取下B柱侧碰传感器后应避免掉落与磕碰，并保持清洁。

Installation procedure安装程序

1. Install the B-pillar side impact sensor1. 安装B柱侧碰传感器

1 Place and adjust the B-pillar side impact sensor A to the installation position, install the fixing bolt ① and tighten it.放置并调整B柱侧碰传感器A到安装位置，安装固定螺栓①并紧固。 Recommended tools: 8mm socket推荐工具：8mm套筒 Torque requirement: 8-12N·m扭矩要求：8-12N•m

2 Connect connector A.连接接插件A。

2. Install the left B-pillar lower trim panel assembly2. 安装左B柱下饰板总成 Reference: Left B-pillar lower trim panel assembly参考：左B柱下饰板总成

3. Install the left B-pillar air outlet assembly3. 安装左侧B柱出风口总成 Reference: Left B-pillar air duct assembly参考：左侧B柱风管总成

4. Install the left rear inner door sill trim assembly.4. 安装左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

5. Install the second row seat cushion assembly5. 安装第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

6. Install the left front inner sill trim panel assembly6. 安装左前内门槛饰板总成 Reference: Left front inner sill trim panel assembly参考：左前内门槛饰板总成

7. Install the left end cover of the instrument panel7. 安装仪表板左侧端盖盖板 Reference: Instrument panel left end cover参考：仪表板左侧端盖盖板

8. Install the left end cover assembly of the instrument panel8. 安装仪表板左侧端盖总成 Reference: Instrument panel left end cover assembly参考：仪表板左侧端盖总成

9. Install the driver’s side lower cover panel assembly9. 安装驾驶侧下护板总成 Reference: Driver's side lower cover panel assembly参考：驾驶侧下护板总成

10. Install the driver's side lower left decorative panel assembly10. 安装驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

11. Connect the negative terminal of the 12V battery, start the vehicle, and check that the airbag indicator light in the instrument cluster should go out.11. 连接蓄电池负极，启动车辆，检查组合仪表安全气囊指示灯应熄灭