Rear window washer nozzle后风窗洗涤喷嘴

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove liftgate switch2. 拆卸举升门开关 Reference: Liftgate switch参考：举升门开关

3. Remove the hatchback door handle box assembly3. 拆卸掀背门拉手盒总成 Reference: Hatchback door handle box assembly参考：掀背门拉手盒总成

4. Remove the hatchback door lower trim panel assembly4. 拆卸掀背门下饰板总成 Reference: Hatchback door lower trim panel assembly参考：掀背门下饰板总成

5. Remove the hatchback door upper trim panel assembly5. 拆卸掀背门上饰板总成 Reference: Hatchback door upper trim panel assembly参考：掀背门上饰板总成

6. Remove the rear wing spoiler assembly6. 拆卸尾翼扰流板总成 Reference: Rear wing spoiler assembly参考：尾翼扰流板总成

7. Remove the rear windshield washer nozzle7. 拆卸后风窗洗涤喷嘴

1 Pry open the through-hole rubber sleeve and disconnect the rear windshield washer nozzle from the windshield washer hose assembly III from point A.撬开过孔胶套，从A处断开后风窗洗涤喷嘴与风窗洗涤软管组件Ⅲ的连接

2 Pry out the rear windshield washer nozzle A.撬出后风窗洗涤喷嘴A。 Recommended tools: Interior parts removal tools推荐工具：内饰件拆卸工具

Installation procedure安装程序

1. Install the rear window washer nozzle1. 安装后风窗洗涤喷嘴

1 Place and adjust rear window washer nozzle A to the installation position and press to ensure it is installed in place.放置并调整后风窗洗涤喷嘴A到安装位置并按压，确保安装到位。

2 Connect the rear windshield washer nozzle and windshield washer hose assembly III from point A, and install the through-hole rubber sleeve.从A处连接后风窗洗涤喷嘴与风窗洗涤软管组件Ⅲ，安装过孔胶套。   Caution:注意： ♦  Check whether the connection between the washing nozzle and the washing pipe is in good condition. If there is water leakage, check and replace it.检查洗涤喷嘴与洗涤管路处连接状态是否良好，若有漏水，检查后更换。

2. Install the rear wing spoiler assembly2. 安装尾翼扰流板总成 Reference: Rear wing spoiler assembly参考：尾翼扰流板总成

3. Install the hatchback door upper trim panel assembly3. 安装掀背门上饰板总成 Reference: Hatchback door upper trim panel assembly参考：掀背门上饰板总成

4. Install the lower hatch trim assembly4. 安装掀背门下饰板总成 Reference: Hatchback door lower trim panel assembly参考：掀背门下饰板总成

5. Install the hatchback door handle box assembly5. 安装掀背门拉手盒总成 Reference: Hatchback door handle box assembly参考：掀背门拉手盒总成

6. Install liftgate switch6. 安装举升门开关 Reference: Liftgate switch参考：举升门开关

7. Connect the negative terminal of the 12V battery7. 连接蓄电池负极