Rear wing spoiler assembly尾翼扰流板总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Connect the negative terminal of the 12V battery.连接蓄电池负极。

2. Remove liftgate switch2. 拆卸举升门开关 Reference: Liftgate switch参考：举升门开关

3. Remove the hatchback door handle box assembly3. 拆卸掀背门拉手盒总成 Reference: Hatchback door handle box assembly参考：掀背门拉手盒总成

4. Remove the hatchback door lower trim panel assembly4. 拆卸掀背门下饰板总成 Reference: Hatchback door lower trim panel assembly参考：掀背门下饰板总成

5. Remove the hatchback door upper trim panel assembly5. 拆卸掀背门上饰板总成 Reference: Hatchback door upper trim panel assembly参考：掀背门上饰板总成

6. Remove the rear wing spoiler assembly6. 拆卸尾翼扰流板总成

1 Remove the fixing bolt ①.拆卸固定螺栓①。 Recommended tools: 10mm socket推荐工具：10mm套筒   Note:提示： ♦  The illustration takes the left side as an example for operation. In actual operation, the left and right sides need to be disassembled.图示以左侧为例进行操作，实际操作中需拆卸左右两侧。

2 Remove the 5 fixing bolts ①.拆卸5颗固定螺栓①。 Recommended tools: 10mm socket推荐工具：10mm套筒 3 Disconnect all connectors and remove the rear wing spoiler assembly.断开所有接插件，取下尾翼扰流板总成。

Installation procedure安装程序

1. Install the rear wing spoiler assembly1. 安装尾翼扰流板总成 1 Connect all connectors.连接所有接插件。

2 Place and adjust the rear wing spoiler to the installation position, install 5 fixing bolts ① and tighten them.放置并调整尾翼扰流板到安装位置，安装5颗固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒

3 Install the fixing bolts ① and tighten them.安装固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒   Note:提示： ♦  The illustration takes the installation on the left side as an example. In actual operation, the left and right sides need to be installed.图示以左侧安装为例，实际操作中需安装左右两侧。

2. Install the hatchback door upper trim panel assembly2. 安装掀背门上饰板总成 Reference: Hatchback door upper trim panel assembly参考：掀背门上饰板总成

3. Install the hatchback door lower trim panel assembly3. 安装掀背门下饰板总成 Reference: Hatchback door lower trim panel assembly参考：掀背门下饰板总成

4. Install the hatchback door handle box assembly4. 安装掀背门拉手盒总成 Reference: Hatchback door handle box assembly参考：掀背门拉手盒总成

5. Install liftgate switch5. 安装举升门开关 Reference: Liftgate switch参考：举升门开关

6. Connect the negative terminal of the 12V battery and start the vehicle. Check that the high-mounted brake lights and rear-facing camera are working properly.6. 连接蓄电池负极，启动车辆。检查高位制动灯及后向摄像头应正常工作。