Combined inertial navigation module组合惯性导航模块

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove the front left seat assembly2. 拆卸前排左座椅总成 Reference: Front left seat assembly参考：前排左座椅总成

3. Remove the driver's side lower left decorative panel assembly3. 拆卸驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

4. Remove the driver’s side lower cover panel assembly4. 拆卸驾驶侧下护板总成 Reference: Driver's side lower cover panel assembly参考：驾驶侧下护板总成

5. Remove the left end cover assembly of the instrument panel5. 拆卸仪表板左侧端盖总成 Reference: Instrument panel left end cover assembly参考：仪表板左侧端盖总成

6. Remove the left end cover of the instrument panel6. 拆卸仪表板左侧端盖盖板 Reference: Instrument panel left end cover参考：仪表板左侧端盖盖板

7. Remove the left front inner sill trim panel assembly7. 拆卸左前内门槛饰板总成 Reference: Left front inner sill trim panel assembly参考：左前内门槛饰板总成

8. Disassemble the combined inertial navigation module8. 拆卸组合惯性导航模块 1 Lift up the carpet under the left front seat.掀起前排左座椅下方地毯。

2 Disconnect connectors A, B, and C, remove the 4 fixing nuts ①, and remove the combined inertial navigation module.断开接插件A、B、C，拆卸4颗固定螺母①，取下组合惯性导航模块。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install the combined inertial navigation module1. 安装组合惯性导航模块

1 Place and adjust the combined inertial navigation module to the installation position, install and tighten 4 fixing nuts ①, and connect connectors A, B, and C.放置并调整组合惯性导航模块到安装位置，安装4颗固定螺母①并紧固，连接接插件A、B、C。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 8-10N·m扭矩要求：8-10N•m 2 Reset the carpet under the front left seat.复位前排左座椅下方地毯。

2. Install the left front inner sill trim panel assembly2. 安装左前内门槛饰板总成 Reference: Left front inner sill trim panel assembly参考：左前内门槛饰板总成

3. Install the left end cover of the instrument panel3. 安装仪表板左侧端盖盖板 Reference: Instrument panel left end cover参考：仪表板左侧端盖盖板

4. Install the left end cover assembly of the instrument panel.4. 安装仪表板左侧端盖总成 Reference: Instrument panel left end cover assembly参考：仪表板左侧端盖总成

5. Install the driver’s side lower cover panel assembly5. 安装驾驶侧下护板总成 Reference: Driver's side lower cover panel assembly参考：驾驶侧下护板总成

6. Install the driver's side lower left decorative panel assembly6. 安装驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

7. Install the front left seat assembly7. 安装前排左座椅总成 Reference: Front left seat assembly参考：前排左座椅总成

8. Connect the negative terminal of the 12V battery. Start the vehicle and check that the combined inertial navigation module should work normally8. 连接蓄电池负极。启动车辆，检查组合惯性导航模块应正常工作