Combination switch and clock spring assembly组合开关与时钟弹簧总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove driver airbag2. 拆卸驾驶员安全气囊 Reference: Driver airbag参考：驾驶员安全气囊

3. Remove the steering wheel assembly3. 拆卸方向盘总成 Reference: Steering wheel assembly参考：方向盘总成

4. Remove the driver's side lower left decorative panel assembly4. 拆卸驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

5. Remove the driver’s side lower cover panel assembly5. 拆卸驾驶侧下护板总成 Reference: Driver's side lower cover panel assembly参考：驾驶侧下护板总成

6. Remove the steering column lower guard assembly6. 拆卸转向管柱下护罩总成 Reference: Steering column lower guard assembly参考：转向管柱下护罩总成

7. Disassemble the combination switch and clock spring assembly7. 拆卸组合开关与时钟弹簧总成

1 Remove the 2 fixing screws ①, pry out the claw A, and remove the combined switch and clock spring assembly B with the wiring harness.拆卸2颗固定螺钉①，撬出卡爪A，取下组合开关与时钟弹簧总成B带线束。 Recommended tools: Phillips screwdriver, interior parts removal tool推荐工具：十字螺丝刀、内饰件拆卸工具 2 Use special tools to lock the clock spring to prevent accidental rotation.使用专用工具锁止时钟弹簧，防止意外转动。 Special Tool: Clock Spring Locking Tool专用工具：时钟弹簧锁止工具

3 Disconnect connectors A, B, C, and D, and remove the combination switch and clock spring assembly.断开接插件A、B、C、D，取下组合开关与时钟弹簧总成。

Installation procedure安装程序

1. Install the combination switch and clock spring assembly1. 安装组合开关与时钟弹簧总成

1 Connect connectors A, B, C, and D to the combination switch and clock spring assembly.连接接插件A、B、C、D，到组合开关与时钟弹簧总成。

2 Place and adjust the combination switch and clock spring assembly B to the installation position, install the claw A, install the 2 fixing screws ① and tighten them.放置并调整组合开关与时钟弹簧总成B到安装位置，安装卡爪A，安装2颗固定螺钉①并紧固。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀

2. Install the steering column lower guard assembly2. 安装转向管柱下护罩总成 Reference: Steering column lower guard assembly参考：转向管柱下护罩总成

3. Install the driver’s side lower cover panel assembly3. 安装驾驶侧下护板总成 Reference: Driver's side lower cover panel assembly参考：驾驶侧下护板总成

4. Install the driver's side lower left decorative panel assembly4. 安装驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

5. Install the steering wheel assembly5. 安装方向盘总成 Reference: Steering wheel assembly参考：方向盘总成

6. Install driver airbag6. 安装驾驶员安全气囊 Reference: Driver airbag参考：驾驶员安全气囊

7. Connect the negative terminal of the 12V battery, start the vehicle, and check that the combination switch should work normally and the airbag indicator light should go out.7. 连接蓄电池负极，启动车辆，检查组合开关应正常工作且安全气囊指示灯应熄灭