Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Drive the vehicle into the lift position, release the parking brake or put it in maintenance mode, and the vehicle power supply is in "OFF" state.将车辆驶入举升机举升位置，解除驻车制动或使其处于维修模式，整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
3 Lift the vehicle.举升车辆。
|
|
|
2. Remove the left rear wheel assembly2. 拆卸左后车轮总成
|
|
|
3. Remove the left rear brake disc3. 拆卸左后制动盘
|
|
|
4. Remove the motor-integrated left rear caliper assembly4. 拆卸电机集成式左后卡钳总成
NOTE： |
|
♦
|
Just hang the caliper to the non-interference position.悬挂卡钳到不干涉位置即可。 |
|
|
|
|
5. Remove the in-line wheel speed sensor (rear)5. 拆卸直插式轮速传感器(后)
|
|
|
6. Remove the left rear axle joint assembly6. 拆卸左后轴节总成
|
|
|
1 Remove 2 fixing nuts and bolts ①, 1 fixing bolt ②, and 1 fixing bolt ③.拆卸2颗固定螺母及螺栓①、1颗固定螺栓②、1颗固定螺栓③。
|
|
Recommended tools: 21mm socket ① ③, 18mm socket ②推荐工具：21mm套筒①③、18mm套筒② |
|
|
|
2 Remove the fixing bolt ① and take off the left rear axle joint assembly.拆卸固定螺栓螺栓①，取下左后轴节总成。
|
|
Recommended tools: 21mm socket推荐工具：21mm套筒 |
|
|
|
3 Remove the 4 fixing bolts ① and separate the left rear axle joint assembly A, the left rear brake disc dust cover B, and the wheel hub bearing C.拆卸4颗固定螺栓①，分离左后轴节总成A、左后制动盘防尘罩B、轮毂轴承C。
|
|
Recommended tools: M12 plum-shaped twelve-point long bit推荐工具：M12梅花型十二角长批头 |
|
Installation procedure安装程序
|
|
1. Install the left rear axle joint assembly1. 安装左后轴节总成
|
|
|
1 Assemble the left rear shaft joint assembly A, the left rear brake disc dust cover B, and the rear hub bearing C to the installation position, install the 4 fixing bolts ① and tighten them.组装左后轴节总成A、左后制动盘防尘罩B、后轮毂轴承C到安装位置，安装4颗固定螺栓①并紧固。
|
|
Recommended tools: M12 plum-shaped twelve-point long bit推荐工具：M12梅花型十二角长批头 |
|
|
Torque requirement: 90-110N·m扭矩要求：90-110N•m |
|
|
|
2 Place and adjust the left rear axle joint assembly to the installation position, install the fixing bolt ① and tighten it.放置并调整左后轴节总成到安装位置，安装固定螺栓①并紧固。
|
|
Recommended tools: 21mm socket推荐工具：21mm套筒 |
|
|
Torque requirement: 180-220N·m扭矩要求：180-220N•m |
|
|
|
3 Install 2 fixing nuts and bolts ①, 1 fixing bolt ②, and 1 fixing bolt ③ and tighten them.安装2颗固定螺母及螺栓①、1颗固定螺栓②、1颗固定螺栓③并紧固。
|
|
Recommended tools: 21mm socket ① ③, 18mm socket ②推荐工具：21mm套筒①③、18mm套筒② |
|
|
Torque requirements: 180-220N·m①③, 115-135N·m②扭矩要求：180-220N•m①③、115-135N•m② |
|
|
|
2. Install the in-line wheel speed sensor (rear)2. 安装直插式轮速传感器(后)
|
|
|
3. Install the motor-integrated left rear caliper assembly3. 安装电机集成式左后卡钳总成
|
|
|
4. Install left rear brake disc4. 安装左后制动盘
|
|
|
5. Install the left rear wheel assembly5. 安装左后车轮总成
|
|
|
6. Carry out four-wheel alignment6. 进行四轮定位
|
|
|
7. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, conduct a road test and check7. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，路试检查
|
Left rear axle assembly (multi-link configuration)左后轴节总成(多连杆配置)
