Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Drive the vehicle into the lift position, release the parking brake or put it in maintenance mode, and the vehicle power supply is in "OFF" state.将车辆驶入举升机举升位置，解除驻车制动或使其处于维修模式，整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
3 Lift the vehicle.举升车辆。
|
|
|
2. Remove the left rear wheel assembly2. 拆卸左后车轮总成
|
|
|
3. Remove the motor-integrated left rear caliper assembly3. 拆卸电机集成式左后卡钳总成
|
|
|
1 Disconnect connector A, remove oil pipe bolt ①, and remove left rear brake hose assembly B.断开接插件A，拆卸油管螺栓①，移开左后制动软管总成B。
|
|
Recommended tools: 11mm socket推荐工具：11mm套筒 |
|
|
CAUTION： |
|
♦
|
Block the brake hose to prevent brake fluid from flowing out.堵塞制动软管，避免制动液流出。 |
|
♦
|
Brake fluid is corrosive, so do not contaminate other parts of the vehicle with brake fluid.制动液具有腐蚀性，不要将制动液沾染到车辆其他部位。 |
|
|
|
|
|
2 Remove the 2 fixing bolts ① and remove the motor-integrated left rear caliper assembly A.拆卸2颗固定螺栓①，取下电机集成式左后卡钳总成A。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
Installation procedure安装程序
|
|
1. Install the motor-integrated left rear caliper assembly1. 安装电机集成式左后卡钳总成
|
|
|
1 Place and adjust the motor-integrated left rear caliper assembly A to the fixed position, install 2 fixing bolts ① and tighten.放置并调整电机集成式左后卡钳总成A到固定位置，安装2颗固定螺栓①并紧固。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
Torque requirement: 100-120N·m扭矩要求：100-120N•m |
|
|
|
2 Install the left rear brake hose assembly B to the fixed position, install the oil pipe bolt ① and tighten it, and connect the connector A.安装左后制动软管总成B到固定位置，安装油管螺栓①并紧固，连接接插件A。
|
|
Recommended tools: 11mm socket推荐工具：11mm套筒 |
|
|
Torque requirement: 24-30N·m扭矩要求：24-30N•m |
|
|
|
CAUTION： |
|
♦
|
Be careful to install copper washers at both ends of the hollow bolts, otherwise brake fluid may leak.注意安装空心螺栓两端铜片垫圈，否则可能导致制动液泄漏。 |
|
♦
|
The copper gasket is a disposable piece and needs to be replaced.铜垫片为一次性件，需更换。 |
|
|
|
|
|
2. Add brake fluid and bleed air2. 加注制动液并排气
|
|
|
3. Install the left rear wheel assembly3. 安装左后车轮总成
|
|
|
4. Land the vehicle and connect the negative terminal of the 12V battery4. 降落车辆，连接蓄电池负极
|
|
|
5. Start the vehicle and drive off the lift, conduct a road test and check5. 起动车辆并驶离举升机，路试检查
|
Motor integrated left rear caliper assembly电机集成式左后卡钳总成
