Windshield washer hose assembly Ⅰ风窗洗涤软管组件Ⅰ

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the left front wheel arch assembly2. 拆卸左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

3. Remove the right front wheel arch assembly3. 拆卸右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

4. Remove the front compartment front upper cover panel assembly4. 拆卸机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

5. Remove the front bumper assembly5. 拆卸前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成   Note:提示： ♦  Just remove the front bumper assembly and accessories as a whole without disassembling them.将前保险杠总成及附件整体拆下即可，不必进行拆分。

6. Remove the left side cover of the wiper cover6. 拆卸雨刮盖板左侧盖板 Reference: Wiper cover left cover参考：雨刮盖板左侧盖板

7. Remove the right side cover of the wiper cover7. 拆卸雨刮盖板右侧盖板 Reference: Wiper cover right side cover参考：雨刮盖板右侧盖板

8. Remove the left scraper arm8. 拆卸左刮臂 Reference: Left scraping arm参考：左刮臂

9. Remove the right scraper arm9. 拆卸右刮臂 Reference: Right scraping arm参考：右刮臂

10. Remove the wiper cover10. 拆卸雨刮盖板 Reference: Wiper cover参考：雨刮盖板

11. Disassemble the windshield washer hose assembly Ⅰ11. 拆卸风窗洗涤软管组件Ⅰ

1 Disconnect the windshield washer hose assembly I from the washer kettle assembly at points A and B.从A、B处断开风窗洗涤软管组件Ⅰ与洗涤水壶总成的连接。

2 Disconnect the windshield washer hose assembly IC from the front windshield left washer nozzle A and the front windshield right washer nozzle B.断开风窗洗涤软管组件ⅠC与前风窗左洗涤喷嘴A、前风窗右洗涤喷嘴B的连接。

3 Disconnect the windshield washer hose assembly IB from the windshield washer hose assembly IIA, disengage the through-hole rubber sleeve, and remove the windshield washer hose assembly IB.断开风窗洗涤软管组件ⅠB与风窗洗涤软管组件ⅡA的连接，脱开过孔胶套，取下风窗洗涤软管组件ⅠB。

Installation procedure安装程序

1. Install windshield washer hose assembly Ⅰ1. 安装风窗洗涤软管组件Ⅰ

1 Place and adjust the windshield washing hose assembly I to the installation position, and connect the windshield washing hose assembly I and the washing kettle assembly at A and B.放置并调整风窗洗涤软管组件Ⅰ到安装位置，在A、B处连接风窗洗涤软管组件Ⅰ与洗涤水壶总成。

2 Connect the windshield washer hose assembly IC to the front windshield left washer nozzle A and the front windshield right washer nozzle B.连接风窗洗涤软管组件ⅠC与前风窗左洗涤喷嘴A、前风窗右洗涤喷嘴B。

3 Install the through-hole rubber sleeve and connect the windshield washer hose assembly IB and the windshield washer hose assembly IIA.安装过孔胶套，连接风窗洗涤软管组件ⅠB与风窗洗涤软管组件ⅡA。

2. Install the front bumper assembly2. 安装前保险杠总成 Reference: Front bumper assembly参考：前保险杠总成

3. Install the front compartment front upper cover panel assembly3. 安装机舱前上护板总成 Reference: Front compartment front upper cover panel assembly参考：机舱前上护板总成

4. Install right front wheel arch assembly4. 安装右前轮眉总成 Reference: Right front wheel arch trim assembly参考：右前轮眉总成

5. Install the left front wheel arch trim assembly5. 安装左前轮眉总成 Reference: Left front wheel arch trim assembly参考：左前轮眉总成

6. Install the left scraper arm6. 安装左刮臂 Reference: Left scraping arm参考：左刮臂

7. Install the right scraper arm7. 安装右刮臂 Reference: Right scraping arm参考：右刮臂

8. Install the left side cover of the wiper cover8. 安装雨刮盖板左侧盖板 Reference: Wiper cover left cover参考：雨刮盖板左侧盖板

9. Install the right side cover of the wiper cover9. 安装雨刮盖板右侧盖板 Reference: Wiper cover right side cover参考：雨刮盖板右侧盖板

10. Install the wiper cover10. 安装雨刮盖板 Reference: Wiper cover参考：雨刮盖板

11. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle, and check that the wiper and washing systems should be working normally.11. 降落车辆，连接蓄电池负极，启动车辆，检查雨刮与洗涤系统应正常工作