Left front door lower hinge左前门下铰链

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。

2. Remove the driver's side lower left decorative panel assembly2. 拆卸驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

3. Remove the driver’s side lower cover panel assembly3. 拆卸驾驶侧下护板总成 Reference: Driver's side lower cover panel assembly参考：驾驶侧下护板总成

4. Remove the left end cover assembly of the instrument panel4. 拆卸仪表板左侧端盖总成 Reference: Instrument panel left end cover assembly参考：仪表板左侧端盖总成

5. Remove the left end cover of the instrument panel5. 拆卸仪表板左侧端盖盖板 Reference: Instrument panel left end cover参考：仪表板左侧端盖盖板

6. Remove the left front inner sill trim panel assembly6. 拆卸左前内门槛饰板总成 Reference: Left front inner sill trim panel assembly参考：左前内门槛饰板总成

7. Remove the left front door lower hinge7. 拆卸左前门下铰链

1 Lock the door and use a marker pen to mark the relative position A on the joint between the left front door and the door frame.锁止车门，使用标记笔在左前车门与门框配合处做相对位置标记A。

2 Remove the 2 fixing bolts ① and remove the wiring harness bracket.拆卸2颗固定螺栓①，移开线束支架。 Recommended tools: 10mm socket推荐工具：10mm套筒

3 Remove the plug cover A and remove the fixing bolt ①.拆卸堵盖A，拆卸固定螺栓①。 Recommended tools: 13mm socket推荐工具：13mm套筒   Caution:注意： ♦  Doors should be firmly fixed to prevent damage to persons or vehicles caused by door movement.应牢固固定车门，防止因车门移动导致人员或车辆损伤。

4 Remove the fixing bolts ① and ②, and remove the left front door lower hinge.拆卸固定螺栓①、固定螺栓②，取下左前门下铰链。 Recommended tools: 13mm socket推荐工具：13mm套筒   Caution:注意： ♦  Doors should be firmly fixed to prevent damage to persons or vehicles caused by door movement.应牢固固定车门，防止因车门移动导致人员或车辆损伤。

Installation procedure安装程序

1. Install the left front door lower hinge1. 安装左前门下铰链

1 Place and adjust the lower hinge of the left front door to the installation position, install and tighten the fixing bolts ① and ②.放置并调整左前门下铰链到安装位置，安装固定螺栓①、固定螺栓②并紧固。 Recommended tools: 13mm socket推荐工具：13mm套筒 Torque requirements: 50-60N·m①, 27-33N·m②扭矩要求：50-60N•m①、27-33N•m②

2 Install the fixing bolt ① and tighten it, and install the plug cover A.安装固定螺栓①并紧固，安装堵盖A。 Recommended tools: 13mm socket推荐工具：13mm套筒 Torque requirement: 27-33N·m扭矩要求：27-33N•m

3 Place and adjust the wiring harness bracket to the installation position, install 2 fixing bolts ① and tighten.放置并调整线束支架到安装位置，安装2颗固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m

4 Adjust the left front door making sure mark A is aligned.调整左前车门，确保标记A对齐。

2. Install the left front inner sill trim panel assembly2. 安装左前内门槛饰板总成 Reference: Left front inner sill trim panel assembly参考：左前内门槛饰板总成

3. Install the left end cover of the instrument panel3. 安装仪表板左侧端盖盖板 Reference: Instrument panel left end cover参考：仪表板左侧端盖盖板

4. Install the left end cover assembly of the instrument panel.4. 安装仪表板左侧端盖总成 Reference: Instrument panel left end cover assembly参考：仪表板左侧端盖总成

5. Install the driver’s side lower cover panel assembly5. 安装驾驶侧下护板总成 Reference: Driver's side lower cover panel assembly参考：驾驶侧下护板总成

6. Install the driver's side lower left decorative panel assembly6. 安装驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

7. Check that the left front door opens and closes normally.7. 检查左前车门开合应正常