Left front door trim panel assembly左前门饰板总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove the left front door switch panel assembly2. 拆卸左前门开关面板总成 Reference: Left front door switch panel assembly参考：左前门开关面板总成

3. Remove the midrange speaker assembly (left front door)3. 拆卸中音扬声器总成(左前门) Reference: Midrange speaker assembly (left front door)参考：中音扬声器总成(左前门)

4. Remove the inner triangle plate assembly of the left front door4. 拆卸左前门内三角板总成 Reference: Left front door inner triangle assembly参考：左前门内三角板总成

5. Remove the left front door trim panel assembly5. 拆卸左前门饰板总成

1 Remove the 2 fixing screws ①, insert a tool on the lower edge of the left front door trim panel assembly and pry, disengage the left front door trim panel assembly fixing clip, lift up and remove the left front door trim panel assembly.拆卸2颗固定螺钉①，在左前门饰板总成下边缘插入工具并撬动，脱开左前门饰板总成固定卡扣，向上提起并取下左前门饰板总成。 Recommended tools: T30 sleeve, interior parts removal tool推荐工具：T30套筒、内饰件拆卸工具   Caution:注意： ♦  When removing the door trim panel assembly, avoid excessive manipulation to avoid breaking the connector harness.脱开门饰板总成时避免操作过当，以防拉断接插件线束。   Caution:注意： ♦  Pay attention to the clip position in the picture.注意图示卡扣位置。 2 Disconnect the connector from the left front door trim assembly.断开与左前门饰板总成连接的接插件。

3 Disengage the door lock cable A and remove the left front door trim panel assembly.脱开门锁拉线A，取下左前门饰板总成。

Installation procedure安装程序

1. Install the left front door trim panel assembly1. 安装左前门饰板总成

1 Connect door lock cable A to the left front door trim assembly.连接门锁拉线A到左前门饰板总成。   Caution:注意： ♦  Check that the pull cord should be securely installed.检查拉线应安装牢固。 2 Connect the connector to the left front door trim panel assembly.连接与左前门饰板总成连接的接插件。

3 Place and adjust the upper edge of the left front door trim panel assembly to the installation position, align the clip position as shown in the figure and press firmly to ensure that it is installed in place, install and tighten the 2 fixing screws ①.放置并调整左前门饰板总成的上部边缘到安装位置，对准图示卡扣位置用力按压，确保安装到位，安装2颗固定螺钉①并紧固。 Recommended tools: T30 socket推荐工具：T30套筒   Caution:注意： ♦  Before installation, check that all clips are missing or damaged. If any, they should be supplemented or replaced.安装前检查所有卡扣应无遗漏、损坏，若有应补充或更换。 ♦  Align the clip position with the mounting hole before pressing to avoid clip damage and missing installation.对准卡扣位置与安装孔后再进行按压，避免卡扣损坏和漏装。   Note:提示： ♦  To facilitate subsequent installation, the wiring harness can be passed through the installation position of the left front door switch panel assembly in advance.为方便后续安装，可提前将线束从左前门开关面板总成安装位置穿出。

2. Install the inner triangle plate assembly of the left front door2. 安装左前门内三角板总成 Reference: Left front door inner triangle assembly参考：左前门内三角板总成

3. Install the midrange speaker assembly (left front door)3. 安装中音扬声器总成(左前门) Reference: Midrange speaker assembly (left front door)参考：中音扬声器总成(左前门)

4. Install the left front door switch panel assembly4. 安装左前门开关面板总成 Reference: Left front door switch panel assembly参考：左前门开关面板总成

5. Connect the negative terminal of the 12V battery5. 连接蓄电池负极