Sub-instrument upper trim panel assembly副仪表板上饰板总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove the driver's side lower left decorative panel assembly2. 拆卸驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

3. Remove the passenger side lower right decorative panel assembly3. 拆卸副驾驶侧右下装饰板总成 Reference: Passenger side lower right decorative panel assembly参考：副驾驶侧右下装饰板总成

4. Remove the left front extension plate assembly4. 拆卸左前延伸板总成 Reference: Left front extension plate assembly参考：左前延伸板总成

5. Remove the right front extension plate assembly5. 拆卸右前延伸板总成 Reference: Right front extension plate assembly参考：右前延伸板总成

6. Remove the switch panel assembly6. 拆卸开关面板总成 Reference: Switch panel assembly参考：开关面板总成

7. Remove the sub-instrument panel body assembly7. 拆卸副仪表板本体总成 Reference: Sub-instrument panel body assembly参考：副仪表板本体总成

8. Remove the upper trim panel assembly on the sub-dashboard8. 拆卸副仪表板上饰板总成

1 Pry out the trim panel assembly A on the secondary instrument panel.撬出副仪表板上饰板总成A。 Recommended tools: Interior parts removal tools推荐工具：内饰件拆卸工具   Note:提示： ♦  Pay attention to the card position at 17 in the picture.注意图示17处卡位置。 2 Disconnect the connector and remove the trim panel assembly on the sub-dashboard.断开接插件，取下副仪表板上饰板总成。

3 Remove the 5 fixing screws ① and take off the central air outlet assembly of the instrument panel.拆卸5颗固定螺钉①，取下仪表板中央出风口总成。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀 4 Disassemble the mobile phone wireless charging module.拆卸手机无线充电模块。 Reference: Mobile phone wireless charging module参考：手机无线充电模块

Installation procedure安装程序

1. Install the upper trim panel assembly on the sub-dashboard1. 安装副仪表板上饰板总成 1 Install the mobile phone wireless charging module.安装手机无线充电模块。 Reference: Mobile phone wireless charging module参考：手机无线充电模块

2 Place and adjust the central air outlet assembly of the instrument panel to the installation position, install 5 fixing screws ① and tighten them.放置并调整仪表板中央出风口总成到安装位置，安装5颗固定螺钉①并紧固。 Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀 3 Connect the connector to the sub-instrument upper trim panel assembly.连接接插件到副仪表上饰板总成。

4 Place and adjust the upper trim panel assembly A of the sub-instrument to the installation position, align the clip position at No. 17 in the figure and press firmly to ensure that it is installed in place.放置并调整副仪表上饰板总成A到安装位置，对准图示17处卡子位置用力按压，确保安装到位。

2. Install the sub-instrument panel body assembly2. 安装副仪表板本体总成 Reference: Sub-instrument panel body assembly参考：副仪表板本体总成

3. Install the switch panel assembly3. 安装开关面板总成 Reference: Switch panel assembly参考：开关面板总成

4. Install right front extension panel assembly4. 安装右前延伸板总成 Reference: Right front extension plate assembly参考：右前延伸板总成

5. Install the left front extension plate assembly5. 安装左前延伸板总成 Reference: Left front extension plate assembly参考：左前延伸板总成

6. Install the passenger side lower right decorative panel assembly6. 安装副驾驶侧右下装饰板总成 Reference: Passenger side lower right decorative panel assembly参考：副驾驶侧右下装饰板总成

7. Install the driver's side lower left decorative panel assembly7. 安装驾驶侧左下装饰板总成 Reference: Driver's side lower left decorative panel assembly参考：驾驶侧左下装饰板总成

8. Connect the negative terminal of the 12V battery8. 连接蓄电池负极