Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
3 Lift the vehicle.举升车辆。
|
|
|
2. Remove the left front wheel assembly2. 拆卸左前车轮总成
|
|
|
3. Remove the left front wheel in-line wheel speed sensor3. 拆卸左前轮直插式轮速传感器
|
|
|
4. Remove the left front drive shaft nut to remove the drive shaft from the wheel hub bearing installation position.4. 拆卸左前驱动轴螺母，使驱动轴脱离轮毂轴承安装位置
Caution:注意： |
|
♦
|
Brush the locking opening of the drive shaft nut completely, otherwise the threads of the drive shaft may be damaged.完全冲开驱动轴螺母的锁止口，否则可能损坏驱动轴的螺纹。 |
|
|
|
|
5. Remove the left front brake disc5. 拆卸左前制动盘
|
|
|
6. Remove the left front wheel hub bearing6. 拆卸左前轮毂轴承
|
|
|
7. Remove the left front brake disc dust cover7. 拆卸左前制动盘防尘罩
|
|
|
8. Remove the left front steering knuckle assembly8. 拆卸左前转向节总成
|
|
|
1 Remove the fixing nuts ① and bolts.拆卸固定螺母①及螺栓。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
|
2 Remove the fixing nut ① and use the ball head removal tool to remove the left front lower swing arm ball head A.拆卸固定螺母①，使用球头拆卸工具，拆卸左前下摆臂球头A。
|
|
Recommended tools: 21mm torx wrench推荐工具：21mm梅花扳手 |
|
|
Special Tools: Ball Head Removal Tool专用工具：球头拆卸工具 |
|
|
|
3 Install the steering knuckle opening tool A to the left front steering knuckle B, rotate the screw ① clockwise to disengage the left front steering knuckle B from the installation position, and remove the left front steering knuckle B.安装转向节张开工具A到左前转向节B，顺时针旋转螺杆①，使左前转向节B脱离安装位置，取下左前转向节B。
|
|
Recommended tools: 22mm socket推荐工具：22mm套筒 |
|
|
Special Tool: Knuckle Opening Tool专用工具：转向节张开工具 |
|
|
|
4 Turn the screw ① counterclockwise and remove the steering knuckle opening tool A.逆时针旋转螺杆①，取下转向节张开工具A。
|
|
Recommended tools: 22mm socket推荐工具：22mm套筒 |
|
Installation procedure安装程序
|
|
1. Install the left front steering knuckle assembly1. 安装左前转向节总成
|
|
|
1 Install the steering knuckle opening tool A to the left front steering knuckle, place and adjust the left front steering knuckle assembly B to the left front strut assembly, rotate the screw ① clockwise, and ensure that the left front steering knuckle assembly B is installed in place.安装转向节张开工具A到左前转向节，放置并调整左前转向节总成B到左前滑柱总成，顺时针旋转螺杆①，确保左前转向节总成B安装到位。
|
|
Recommended tools: 22mm socket推荐工具：22mm套筒 |
|
|
Special Tool: Knuckle Opening Tool专用工具：转向节张开工具 |
|
|
|
2 Turn the screw ① counterclockwise and remove the steering knuckle opening tool A.逆时针旋转螺杆①，取下转向节张开工具A。
|
|
Recommended tools: 22mm socket推荐工具：22mm套筒 |
|
|
|
3 Place and adjust the left front lower swing arm ball head A to the installation position, install the fixing nut ① and tighten it.放置并调整左前下摆臂球头A到安装位置，安装固定螺母①并紧固。
|
|
Recommended tools: 21mm torx wrench推荐工具：21mm梅花扳手 |
|
|
Torque requirement: 108-132N·m扭矩要求：108-132N•m |
|
|
|
4 Install the fixing bolts and nuts ① and tighten them.安装固定螺栓及螺母①并紧固。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
Torque requirement: 99-121N·m扭矩要求：99-121N•m |
|
|
|
2. Install the left front wheel hub bearing2. 安装左前轮毂轴承
|
|
|
3. Install the left front brake disc dust cover3. 安装左前制动盘防尘罩
|
|
|
4. Install the left front brake disc4. 安装左前制动盘
|
|
|
5. Install the left front drive shaft nut5. 安装左前驱动轴螺母
|
|
|
6. Install the left front wheel in-line wheel speed sensor6. 安装左前轮直插式轮速传感器
|
|
|
7. Install the left front wheel assembly7. 安装左前车轮总成
|
|
|
8. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, conduct a road test and check8. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，路试检查
|
Left front steering knuckle assembly左前转向节总成
