Left rear brake pipe II左后制动硬管Ⅱ

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the left side skirt assembly2. 拆卸左侧裙板总成 Reference: Left side skirt assembly参考：左侧裙板总成

3. Remove the right side skirt assembly3. 拆卸右侧裙板总成 Reference: Right skirt assembly参考：右侧裙板总成

4. Remove the front compartment front lower cover panel assembly4. 拆卸机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

5. Drain the coolant from the temperature control system5. 排放温控系统冷却液 Reference: Temperature control system coolant参考：温控系统冷却液

6. Remove the four wheel assemblies6. 拆卸四个车轮总成 Reference: Wheel assembly参考：车轮总成

7. Drain brake fluid7. 排放制动液 Reference: brake fluid参考：制动液

8. Remove the battery pack assembly8. 拆卸电池组箱总成 Reference: Battery pack assembly参考：电池组箱总成

9. Remove the left rear brake pipe II9. 拆卸左后制动硬管Ⅱ

1 Remove the oil pipe joint nut ① and disconnect the left rear brake pipe Ⅱ from the brake pipe connector.拆卸油管接头螺母①，断开左后制动硬管Ⅱ与制动硬管连接器的连接。 Recommended tools: 10mm tubing wrench推荐工具：10mm油管扳手

2 Remove the oil pipe joint nut ① and disconnect the left rear brake hard pipe IIA from the left rear brake hose assembly.拆卸油管接头螺母①，断开左后制动硬管ⅡA与左后制动软管总成的连接。 Recommended tools: 10mm tubing wrench推荐工具：10mm油管扳手 3 Disengage the pipe fixing clip and take out the left rear brake hard pipe II.脱开管路固定卡，取出左后制动硬管Ⅱ。

Installation procedure安装程序

1. Install the left rear brake pipe II1. 安装左后制动硬管Ⅱ 1 Place and adjust the left rear brake hard pipe II to the installation position, and install the pipe fixing clip.放置并调整左后制动硬管Ⅱ到安装位置，安装管路固定卡。

2 Connect the left rear brake hard pipe IIA to the left rear brake hose assembly, install the oil pipe joint nut ① and tighten it.连接左后制动硬管ⅡA到左后制动软管总成，安装油管接头螺母①并紧固。 Recommended tools: 10mm tubing wrench推荐工具：10mm油管扳手 Torque requirement: 15-19N·m扭矩要求：15-19N•m

3 Connect the left rear brake pipe II to the brake pipe connector, install the oil pipe joint nut ① and tighten it.连接左后制动硬管Ⅱ到制动硬管连接器，安装油管接头螺母①并紧固。 Recommended tools: 10mm tubing wrench推荐工具：10mm油管扳手 Torque requirement: 15-19N·m扭矩要求：15-19N•m

2. Install the battery pack assembly2. 安装电池组箱总成 Reference: Battery pack assembly参考：电池组箱总成

3. Fill the temperature control system coolant3. 加注温控系统冷却液 Reference: Temperature control system coolant参考：温控系统冷却液

4. Add brake fluid and bleed the air.4. 加注制动液并排气 Reference: brake fluid参考：制动液

5. Install the front compartment front lower cover panel assembly5. 安装机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

6. Install the four wheel assemblies6. 安装四个车轮总成 Reference: Wheel assembly参考：车轮总成

7. Install the right side skirt assembly7. 安装右侧裙板总成 Reference: Right skirt assembly参考：右侧裙板总成

8. Install the left side skirt assembly8. 安装左侧裙板总成 Reference: Left side skirt assembly参考：左侧裙板总成

9. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, conduct a road test and check9. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，路试检查