|
|
Note:提示： |
|
♦
|
The disassembly and assembly procedures for the left and right rear coil springs (multi-link configuration) are basically the same. The following content takes the left side as an example.左、右后螺旋弹簧(多连杆配置)的拆装程序基本相同，下述内容以左侧为例进行操作。 |
|
|
Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制 动，整车电源处于“OFF”状态。
2 Lift the vehicle.举升车辆。
|
|
|
2. Remove the left rear wheel assembly2. 拆卸左后车轮总成
|
|
|
3. Remove the rear floor guard body (multi-link configuration)3. 拆卸后地板后下护板本体(多连杆配置)
|
|
|
4. Remove the rear coil spring4. 拆卸后螺旋弹簧
|
|
|
1 Use the hydraulic bracket to lift the left rear lower arm assembly, remove 2 fixing bolts ①, loosen 1 fixing nut and bolt ②, slowly lower the hydraulic bracket, and remove the rear coil spring.使用液压托架托举左后下臂总成，拆卸2颗固定螺栓①、拧松1颗固定螺母及螺栓②，缓慢降下液压托架，取下后螺旋弹簧。
|
|
Recommended tools: 21mm socket, hydraulic bracket推荐工具：21mm套筒、液压托架 |
|
|
|
2 Remove the rubber pad A under the rear spring.取出后弹簧下橡胶垫A。
|
|
|
3 Remove the rubber pad A on the spring.取出后弹簧上橡胶垫A。
|
Installation procedure安装程序
|
|
1. Install rear coil spring1. 安装后螺旋弹簧
|
|
|
1 Place and adjust the rear spring upper rubber pad A to the installation position.放置并调整后弹簧上橡胶垫A到安装位置。
|
|
|
2 Place and adjust the rear lower spring rubber pad A to the installation position, and use the hydraulic bracket to support the left rear lower arm assembly.放置并调整后弹簧下橡胶垫A到安装位置， 使用液压托架托起左后下臂总成。
|
|
Recommended tools: Hydraulic bracket推荐工具：液压托架 |
|
|
|
3 Place and adjust the rear coil spring to the installation position, install 2 fixing bolts ①, 1 fixing bolt and nut ② and tighten them.放置并调整后螺旋弹簧到安装位置，安装2颗固定螺栓①、1颗固定螺栓及螺母②并紧固。
|
|
Recommended tools: 21mm socket, hydraulic bracket推荐工具：21mm套筒、液压托架 |
|
|
Torque requirement: 180-220N·m扭矩要求：180-220N•m |
|
|
|
2. Install the rear floor guard body (multi-link configuration)2. 安装后地板后下护板本体(多连杆配置)
|
|
|
3. Install the left rear wheel assembly3. 安装左后车轮总成
|
|
|
4. Carry out four-wheel alignment4. 进行四轮定位
|
|
|
5. Land the vehicle, start the vehicle and drive off the lift, conduct road test and check5. 降落车辆，起动车辆并驶离举升机，路试检查
|
Rear coil spring (multi-link configuration)后螺旋弹簧(多连杆配置)
