Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Park the vehicle on a flat road, activate the parking brake, and turn the vehicle power supply to "OFF".将车辆停在平坦路面，启用驻车制动，整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
|
|
|
2. Remove the hatchback door sill trim panel assembly2. 拆卸掀背门门槛饰板总成
|
|
|
3. Remove the second row seat cushion assembly3. 拆卸第二排座椅坐垫总成
|
|
|
4. Remove the left rear inner sill trim panel assembly4. 拆卸左后内门槛饰板总成
|
|
|
5. Remove the second row left seat back assembly5. 拆卸第二排左座椅靠背总成
|
|
|
6. Remove the trunk light6. 拆卸行李箱灯
|
|
|
7. Remove the second row left backrest connection bracket7. 拆卸第二排左靠背连接支架
|
|
|
8. Remove the left C-pillar lower trim panel assembly8. 拆卸左C柱下饰板总成
|
|
|
9. Remove the left C-pillar upper trim panel assembly9. 拆卸左C柱上饰板总成
|
|
|
10. Remove the second row backrest left lock bracket assembly10. 拆卸第二排靠背左锁扣支架总成
|
|
|
1 Remove the fixing screw ①.拆卸固定螺钉①。
|
|
Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀 |
|
|
|
2 Remove the 2 fixing nuts ① and remove the second row backrest left lock bracket assembly.拆卸2颗固定螺母①，取下第二排靠背左锁扣支架总成。
|
|
Recommended tools: 15mm socket推荐工具：15mm套筒 |
|
Installation procedure安装程序
|
|
1. Install the second row backrest left lock bracket assembly1. 安装第二排靠背左锁扣支架总成
|
|
|
1 Place and adjust the second row backrest left lock bracket assembly to the installation position, install 2 fixing nuts ① and tighten.放置并调整第二排靠背左锁扣支架总成到安装位置，安装2颗固定螺母①并紧固。
|
|
Recommended tools: 15mm socket推荐工具：15mm套筒 |
|
|
Torque requirement: 20-24N·m扭矩要求：20-24N•m |
|
|
|
2 Install the fixing screw ① and tighten.安装固定螺钉①并紧固。
|
|
Recommended tools: Phillips screwdriver推荐工具：十字螺丝刀 |
|
|
|
2. Install the left C-pillar upper trim panel assembly2. 安装左C柱上饰板总成
|
|
|
3. Install the left C-pillar lower trim panel assembly3. 安装左C柱下饰板总成
|
|
|
4. Install the second row left backrest connection bracket4. 安装第二排左靠背连接支架
|
|
|
5. Install trunk light5. 安装行李箱灯
|
|
|
6. Install the second row left seat back assembly6. 安装第二排左座椅靠背总成
|
|
|
7. Install the left rear inner sill trim panel assembly7. 安装左后内门槛饰板总成
|
|
|
8. Install the second row seat cushion assembly8. 安装第二排座椅坐垫总成
|
|
|
9. Install hatchback door sill trim panel assembly9. 安装掀背门门槛饰板总成
|
|
|
10. Connect the negative terminal of the 12V battery and check that the rear left backrest assembly can be folded and locked normally.10. 连接蓄电池负极，检查后排左靠背总成应能正常折叠、锁止
|
Second row backrest left lock bracket assembly第二排靠背左锁扣支架总成
