Autonomous Driving Domain Controller Bracket自动驾驶域控制器支架

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and put the vehicle's power supply in the "OFF" state.将车辆停在平坦路面，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Remove the passenger side lower right decorative panel assembly2. 拆卸副驾驶侧右下装饰板总成 Reference: Passenger side lower right decorative panel assembly参考：副驾驶侧右下装饰板总成

3. Remove the right end cover assembly of the instrument panel3. 拆卸仪表板右侧端盖总成 Reference: Instrument panel right end cover assembly参考：仪表板右侧端盖总成

4. Remove the end cover on the right side of the instrument panel4. 拆卸仪表板右侧端盖盖板 Reference: Instrument panel right end cover参考：仪表板右侧端盖盖板

5. Remove the right front inner sill trim panel assembly5. 拆卸右前内门槛饰板总成 Reference: Right front inner sill trim panel assembly参考：右前内门槛饰板总成

6. Remove the front right seat assembly6. 拆卸前排右座椅总成 Reference: Front right seat assembly参考：前排右座椅总成

7. Remove the second row seat cushion assembly7. 拆卸第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

8. Remove the right rear inner sill trim panel assembly8. 拆卸右后内门槛饰板总成 Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

9. Remove the right B-pillar air outlet assembly9. 拆卸右侧B柱出风口总成 Reference: Right B-pillar air outlet assembly参考：右侧B柱出风口总成

10. Remove the right B-pillar lower trim panel assembly10. 拆卸右B柱下饰板总成 Reference: Right B-pillar lower trim panel assembly参考：右B柱下饰板总成

11. Remove the anti-trampling bracket of the autonomous driving domain controller11. 拆卸自动驾驶域控制器防踩踏支架 Reference: Autonomous Driving Domain Controller Anti-Trampling Bracket参考：自动驾驶域控制器防踩踏支架

12. Disassemble the autonomous driving domain controller12. 拆卸自动驾驶域控制器 Reference: Autonomous Driving Domain Controller参考：自动驾驶域控制器

13. Remove the autonomous driving domain controller bracket13. 拆卸自动驾驶域控制器支架

1 Remove the 4 fixing nuts ① and remove the autonomous driving domain controller bracket.拆卸4颗固定螺母①，取下自动驾驶域控制器支架。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install the autonomous driving domain controller bracket1. 安装自动驾驶域控制器支架

1 Place and adjust the automatic driving domain controller bracket to the installation position, install 4 fixing nuts ① and tighten them.放置并调整自动驾驶域控制器支架到安装位置，安装4颗固定螺母①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m

2. Install the autonomous driving domain controller2. 安装自动驾驶域控制器 Reference: Autonomous Driving Domain Controller参考：自动驾驶域控制器

3. Install the anti-trampling bracket of the autonomous driving domain controller3. 安装自动驾驶域控制器防踩踏支架 Reference: Autonomous Driving Domain Controller Anti-Trampling Bracket参考：自动驾驶域控制器防踩踏支架

4. Install the right B-pillar lower trim panel assembly4. 安装右B柱下饰板总成 Reference: Right B-pillar lower trim panel assembly参考：右B柱下饰板总成

5. Install the right B-pillar air outlet assembly5. 安装右侧B柱出风口总成 Reference: Right B-pillar air outlet assembly参考：右侧B柱出风口总成

6. Install the right rear inner sill trim panel assembly6. 安装右后内门槛饰板总成 Reference: Right rear inner sill trim panel assembly参考：右后内门槛饰板总成

7. Install the second row seat cushion assembly7. 安装第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

8. Install the front right seat assembly8. 安装前排右座椅总成 Reference: Front right seat assembly参考：前排右座椅总成

9. Install the right front inner sill trim panel assembly9. 安装右前内门槛饰板总成 Reference: Right front inner sill trim panel assembly参考：右前内门槛饰板总成

10. Install the right end cover of the instrument panel10. 安装仪表板右侧端盖盖板 Reference: Instrument panel right end cover参考：仪表板右侧端盖盖板

11. Install the right end cover assembly of the instrument panel11. 安装仪表板右侧端盖总成 Reference: Instrument panel right end cover assembly参考：仪表板右侧端盖总成

12. Install the passenger side lower right decorative panel assembly12. 安装副驾驶侧右下装饰板总成 Reference: Passenger side lower right decorative panel assembly参考：副驾驶侧右下装饰板总成

13. Connect the negative terminal of the 12V battery13. 连接蓄电池负极