DTC list故障码(DTC)列表
|
No.序号 |
DTC故障码 |
Fault code description故障码描述 |
Possible reasons可能原因 |
Solution解决办法 |
|---|---|---|---|---|
|
1
|
P14A913
|
Main relay control circuit is open主继电器控制电路开路
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
2
|
P14A912
|
Main relay control circuit short power supply主继电器控制电路短电源
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
3
|
P14A911
|
Main relay control circuit short to ground主继电器控制电路短地
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
4
|
P140296
|
Sensor power supply 2 integrated fault传感器供电电源2集成故障
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
5
|
P140217
|
Sensor power supply 2 overvoltage传感器供电电源2过压
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
6
|
P140211
|
Sensor power supply 2 is short-circuited to ground传感器供电电源2短路到地
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
7
|
P140216
|
Sensor power supply 2 undervoltage传感器供电电源2欠压
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
8
|
P140396
|
Sensor power supply 3 integrated fault传感器供电电源3集成故障
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
9
|
P140317
|
Sensor power supply 3 overvoltage传感器供电电源3过压
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
10
|
P140311
|
Sensor power supply 3 is short-circuited to ground传感器供电电源3短路到地
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
11
|
P140316
|
Sensor power supply 3 undervoltage传感器供电电源3欠压
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
12
|
P146145
|
memory read error内存读取错误
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
13
|
P146245
|
memory write error内存写入错误
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
14
|
P146345
|
memory overflow内存溢出
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
15
|
P146401
|
Analog-to-digital converter pull-down test failed模数转换器下拉测试失败
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
16
|
P146501
|
Analog to Digital Converter Reference Supply Test Failed模数转换器参考电源测试失败
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
17
|
P146001
|
High-speed CAN hardware register failure高速CAN硬件寄存器故障
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
18
|
P146694
|
Unexpected restart非预期重启
|
1. Hardware underlying failure1.硬件底层故障
|
|
|
19
|
P14E011
|
Emergency power off hard wire short circuit to ground紧急下电硬线短路到地
|
1. Emergency power-off hard wires are damaged, and the wiring harness or interface is short-circuited to ground.1.紧急下电硬线损坏、线束或接口短路到地
|
|
|
20
|
P14E012
|
Emergency power off Hardwire short circuit to power supply紧急下电硬线短路到电源
|
1. Emergency power-off hard wires are damaged, and the wiring harness or interface is short-circuited to the power supply.1.紧急下电硬线损坏、线束或接口短路到电源
|
|
|
21
|
P14E013
|
Emergency power off and hard wire open circuit紧急下电硬线开路
|
1. Emergency power-off hard wire is damaged, wiring harness or interface is open circuit1.紧急下电硬线损坏、线束或接口开路
|
|
|
22
|
P14A311
|
Electronic lock driver short circuit to ground电子锁驱动短路到地
|
1. The electronic lock is damaged, and the wiring harness or interface is short-circuited to ground.1.电子锁损坏、线束或接口短路到地
|
|
|
23
|
P14A312
|
Electronic lock driver short circuit to power supply电子锁驱动短路到电源
|
1. The electronic lock is damaged, the wiring harness or interface is short-circuited to the power supply1.电子锁损坏、线束或接口短路到电源
|
|
|
24
|
P14A319
|
Electronic lock driver overcurrent电子锁驱动过流
|
1. The electronic lock is damaged, the wiring harness or interface is faulty1.电子锁损坏、线束或接口故障
|
|
|
25
|
P14A313
|
Electronic lock driver open circuit电子锁驱动开路
|
1. The electronic lock is damaged, the wiring harness or interface is open circuit1.电子锁损坏、线束或接口开路
|
|
|
26
|
P144191
|
Collision hard line PWM is not within the reasonable range碰撞硬线PWM不在合理范围
|
1. Collision hard wire failure, wiring harness failure or interface failure1.碰撞硬线故障、线束故障或接口故障
|
|
|
27
|
P141517
|
Accelerator pedal 1 depth feedback line voltage is too high加速踏板1深度反馈线电压过高
|
1. Accelerator pedal 1 depth sensor failure, wiring harness failure or interface failure1.加速踏板1深度传感器故障、线束故障或接口故障
|
|
|
28
|
P141516
|
Accelerator pedal 1 depth feedback line voltage is too low加速踏板1深度反馈线电压过低
|
1. Accelerator pedal 1 depth sensor failure, wiring harness failure or interface failure1.加速踏板1深度传感器故障、线束故障或接口故障
|
|
|
29
|
P141617
|
Accelerator pedal 2 depth feedback line voltage is too high加速踏板2深度反馈线电压过高
|
1. Accelerator pedal 2 depth sensor failure, wiring harness failure or interface failure1.加速踏板2深度传感器故障、线束故障或接口故障
|
|
|
30
|
P141616
|
Accelerator pedal 2 depth feedback line voltage is too low加速踏板2深度反馈线电压过低
|
1. Accelerator pedal 2 depth sensor failure, wiring harness failure or interface failure1.加速踏板2深度传感器故障、线束故障或接口故障
|
|
|
31
|
P141917
|
DC fast charging positive electrode temperature feedback voltage is too high快充正极温度反馈电压过高
|
1. DC fast charging positive temperature sensor failure, wiring harness failure or interface failure1.快充正极温度传感器故障、线束故障或接口故障
|
|
|
32
|
P141916
|
DC fast charging positive temperature feedback voltage is too low快充正极温度反馈电压过低
|
1. DC fast charging positive temperature sensor failure, wiring harness failure or interface failure1.快充正极温度传感器故障、线束故障或接口故障
|
|
|
33
|
P141A17
|
DC fast charging negative electrode temperature feedback voltage is too high快充负极温度反馈电压过高
|
1. DC fast charging negative temperature sensor failure, wiring harness failure or interface failure1.快充负极温度传感器故障、线束故障或接口故障
|
|
|
34
|
P141A16
|
DC fast charging negative electrode temperature feedback voltage is too low快充负极温度反馈电压过低
|
1. DC fast charging negative temperature sensor failure, wiring harness failure or interface failure1.快充负极温度传感器故障、线束故障或接口故障
|
|
|
35
|
P141B17
|
AC charging L1 temperature feedback voltage is too high慢充L1温度反馈电压过高
|
1. AC charging L1 temperature sensor failure, wiring harness failure or interface failure1.慢充L1温度传感器故障、线束故障或接口故障
|
|
|
36
|
P141B16
|
AC charging L1 temperature feedback voltage is too low慢充L1温度反馈电压过低
|
1. AC charging L1 temperature sensor failure, wiring harness failure or interface failure1.慢充L1温度传感器故障、线束故障或接口故障
|
|
|
37
|
P141C17
|
AC charge N temperature feedback voltage is too high慢充N温度反馈电压过高
|
1. AC charging N temperature sensor failure, wiring harness failure or interface failure1.慢充N温度传感器故障、线束故障或接口故障
|
|
|
38
|
P141C16
|
AC charge N temperature feedback voltage is too low慢充N温度反馈电压过低
|
1. AC charging N temperature sensor failure, wiring harness failure or interface failure1.慢充N温度传感器故障、线束故障或接口故障
|
|
|
39
|
P144F91
|
Abnormal temperature of DC fast-charging plug快充枪温度异常
|
1. The DC fast-charging plug terminal connection is abnormal or there is foreign matter1.快充枪端子连接异常或者存在异物
|
|
|
40
|
P144398
|
Abnormal temperature of AC charging plug慢充枪温度异常
|
1. The AC charging plug terminal connection is abnormal or there is foreign matter1.慢充枪端子连接异常或者存在异物
|
|
|
41
|
P141A01
|
DC fast charging positive and negative temperature sensors both failed快充正负极温度传感器均失效
|
1. The temperature sensor of the DC fast charging port is abnormal or the wiring harness is abnormal.1.快充口温度传感器异常或者线束异常
|
|
|
42
|
P141B01
|
Both the positive and negative temperature sensors of AC charging failed.慢充正负极温度传感器均失效
|
1. The AC charging port temperature sensor is abnormal or the wiring harness is abnormal.1.慢充口温度传感器异常或者线束异常
|
|
|
43
|
P149001
|
Power-on initialization failure上电初始化故障
|
1. Precharge conditions are not met1.预充条件不满足
|
|
|
44
|
P149009
|
Power-on failure上电失败故障
|
1. Power-on timeout1.上电超时
|
|
|
45
|
P147192
|
The BMS status is incorrect during the power-on initialization phase.上电初始化阶段BMS状态不正确
|
1.The BMS mode is incorrect1.BMS模式不正确
|
|
|
46
|
P147292
|
The DCU status is incorrect during the power-on initialization phase.上电初始化阶段DCU状态不正确
|
1.DCU mode is incorrect1.DCU模式不正确
|
|
|
47
|
P147692
|
The DCDC status is incorrect during the power-on initialization phase.上电初始化阶段DCDC状态不正确
|
1.DCDC mode is incorrect1.DCDC模式不正确
|
|
|
48
|
P147592
|
The OBC status is incorrect during the power-on initialization phase.上电初始化阶段OBC状态不正确
|
1.OBC mode is incorrect1.OBC模式不正确
|
|
|
49
|
P147194
|
BMS status is incorrect during power-on process上电过程BMS状态不正确
|
1.The BMS mode is incorrect1.BMS模式不正确
|
|
|
50
|
P147294
|
DCU status is incorrect during power-on process上电过程DCU状态不正确
|
1.DCU mode is incorrect1.DCU模式不正确
|
|
|
51
|
P147694
|
DCDC status is incorrect during power-on process上电过程DCDC状态不正确
|
1.DCDC mode is incorrect1.DCDC模式不正确
|
|
|
52
|
P147594
|
OBC status is incorrect during power-on process上电过程OBC状态不正确
|
1.OBC mode is incorrect1.OBC模式不正确
|
|
|
53
|
P147109
|
Insufficient high-voltage battery capacity during power-on process上电过程动力电池能力不足
|
1. Insufficient high-voltage battery capacity1.动力电池能力不足
|
|
|
54
|
P149063
|
Motor rapid discharge timeout fault when powering off下电时电机快速放电超时故障
|
1. When powering off, the motor is in rapid discharge mode and the voltage drops over time.1.下电时，电机快速放电模式，电压下降超时
|
|
|
55
|
P148062
|
Anti-theft authentication failed - wrong key防盗认证失败-钥匙错误
|
1.PEPS and VCU authentication failed; wrong key1.PEPS与VCU认证失败；钥匙错误
|
|
|
56
|
P148162
|
Anti-theft not matching fault防盗未匹配故障
|
1.Virgin’s ECU has not yet been matched.1.Virgin的ECU,尚未经过匹配
|
|
|
2. There was a problem during the matching process and the matching was not successful.2.匹配过程中出现问题，未匹配成功
|
||||
|
3.ESK is lost3.ESK丢失
|
||||
|
57
|
P148300
|
Anti-theft communication failed - no reply received防盗通讯失败-未收到回复
|
1. No PEPS reply received1.没有收到PEPS回复
|
|
|
58
|
P148500
|
Anti-theft authentication failed - anti-theft device busy防盗认证失败-防盗器busy
|
1.PEPS returns to continuous busy state;1.PEPS回复持续busy状态；
|
|
|
59
|
P148600
|
Anti-theft authentication failed - wrong encryption result防盗认证失败-加密结果错误
|
1.PEPS and VCU authentication failed; encryption result is wrong1.PEPS与VCU认证失败；加密结果错误
|
|
|
60
|
P148700
|
Anti-theft authentication failed - incorrect format防盗认证失败-格式不正确
|
1.The PEPS reply status word format is incorrect1.PEPS回复状态字格式不正确
|
|
|
61
|
P148A62
|
Anti-theft-remote-unmatched fault防盗-远程-未匹配故障
|
1. Not consistent with the remote anti-theft process1.与远程防盗流程不符合
|
|
|
62
|
P148D00
|
Anti-theft-remote-authentication failure-encryption result error防盗-远程-认证失败-加密结果错误
|
1. Not consistent with the remote anti-theft process1.与远程防盗流程不符合
|
|
|
63
|
P140017
|
VCU power supply voltage is too high 16VVCU供电电压过高16V
|
1.VCU power supply port failure, wiring harness failure or interface failure1.VCU供电口故障、线束故障或接口故障
|
|
|
64
|
P140016
|
VCU power supply voltage is too low 9VVCU供电电压过低9V
|
1.VCU power supply port failure, wiring harness failure or interface failure1.VCU供电口故障、线束故障或接口故障
|
|
|
65
|
P140416
|
VCU supply voltage is lower than 11VVCU供电电压低于11V
|
1. The power supply voltage is low1.供电电压偏低
|
|
|
66
|
P14E162
|
Electronic lock status verification failed电子锁状态校验失败
|
1. The electronic lock status does not match1.电子锁状态不匹配
|
|
|
67
|
P14E377
|
P (Park) lock engagement failedP档挂锁失败
|
1.P (Park) request is unsuccessful or P (Park) lock is stuck1.P档请求不成功或P档锁卡住
|
|
|
68
|
P14E577
|
Electronic lock failed to lock电子锁落锁失败
|
1. The electronic lock request is unsuccessful or the electronic lock is stuck.1.电子锁请求不成功或电子锁卡住
|
|
|
69
|
P14E677
|
Unlocking of electronic lock failed电子锁解锁失败
|
1. The electronic lock request is unsuccessful or the electronic lock is stuck.1.电子锁请求不成功或电子锁卡住
|
|
|
70
|
P0A0A01
|
high-voltage interlock (HVIL) circuit hard wiring abnormality高压互锁回路硬线异常
|
1. high-voltage interlock (HVIL) circuit hard-wire failure1.高压互锁回路硬线故障
|
|
|
71
|
P0A0A29
|
high-voltage interlock (HVIL) circuit abnormality高压互锁回路异常
|
1. high-voltage interlock (HVIL) circuit failure1.高压互锁回路故障
|
|
|
72
|
P144262
|
Brake switch signal does not match制动开关信号不匹配
|
1. The brake switch signal is abnormal1.制动开关信号异常
|
|
|
73
|
P144362
|
Brake pedal position sensor signal does not match brake switch signal制动踏板位置传感器信号与制动开关信号不匹配
|
1. The brake pedal position sensor signal is inconsistent with the brake pedal status reflected by the brake switch signal.1.制动踏板位置传感器信号与制动开关信号所反映的制动踏板状态不一致
|
|
|
74
|
P144462
|
The two accelerator pedal position sensor signals do not match两个油门踏板位置传感器信号不匹配
|
1. The accelerator pedal status reflected by the accelerator pedal position sensor 1 signal and the accelerator pedal position sensor 2 signal is inconsistent1.油门踏板位置传感器1信号与油门踏板位置传感器2信号所反映的油门踏板状态不一致
|
|
|
75
|
P144562
|
Accelerator pedal signal failure加速踏板信号失效
|
1. The accelerator pedal position sensor 1 is faulty and the fault 2 lasts for more than 500ms.1.油门踏板位置传感器1故障且2故障超过500ms
|
|
|
76
|
P144662
|
P (Park) control request fails (EPB linkage model)P档控制请求失效（EPB联动车型）
|
1. The voltage signals of gear selection signal lines 0, 1, 2, and 3 are abnormal.1.选档信号线0、1、2、3电压信号异常
|
|
|
77
|
P143509
|
Abnormal status of cruise button巡航按钮状态异常
|
1. Cruise button failure, wiring harness failure or interface failure1.巡航按钮故障、线束故障或接口故障
|
|
|
78
|
P144A86
|
Vehicle speed failure车速失效故障
|
1. Unable to obtain vehicle speed source1.无法获得车速来源
|
|
|
79
|
P144C00
|
Vehicle collision failure车辆发生碰撞故障
|
1. Vehicle collision1.车辆发生碰撞
|
|
|
80
|
P145196
|
Inverse TCS function failure逆TCS功能失效
|
1. Communication failure with ESP1.与ESP通讯故障
|
|
|
81
|
P144794
|
Non-factory mode is turned on and automatic return to P is prohibited.非工厂模式开启禁止自动回P
|
1. Missing writing at factory offline inspection station1.工厂下线检测工位漏写
|
|
|
82
|
U108488
|
ECAN bus off (long time)ECAN总线关闭（长时）
|
1. Communication failure1.通讯故障
|
|
|
83
|
U108188
|
PCAN bus off (long time)PCAN总线关闭（长时）
|
1. Communication failure1.通讯故障
|
|
|
84
|
U108288
|
ACAN bus off (long time)ACAN总线关闭（长时）
|
1. Communication failure1.通讯故障
|
|
|
85
|
U011187
|
Communication with BMS lost与BMS通信丢失
|
1. Communication failure1.通讯故障
|
|
|
86
|
U041281
|
Received invalid message from BMS接收到BMS的无效报文
|
1. Communication failure1.通讯故障
|
|
|
87
|
U029287
|
Communication with DCU lost与DCU通信丢失
|
1. Communication failure1.通讯故障
|
|
|
88
|
U059481
|
Invalid message received from DCU接收到DCU的无效报文
|
1. Communication failure1.通讯故障
|
|
|
89
|
U029887
|
Communication with DCDC lost与DCDC通信丢失
|
1. Communication failure1.通讯故障
|
|
|
90
|
U059981
|
Invalid message received from DCDC接收到DCDC的无效报文
|
1. Communication failure1.通讯故障
|
|
|
91
|
U011287
|
Communication with OBC lost与OBC通信丢失
|
1. Communication failure1.通讯故障
|
|
|
92
|
U041381
|
Invalid message received from OBC接收到OBC的无效报文
|
1. Communication failure1.通讯故障
|
|
|
93
|
P182687
|
Communication with ITS lost与ITS通信丢失
|
1. Communication failure1.通讯故障
|
|
|
94
|
P182686
|
Invalid message received from ITS接收到ITS的无效报文
|
1. Communication failure1.通讯故障
|
|
|
95
|
U019887
|
Communication with TEL lost与TEL通信丢失
|
1. Communication failure1.通讯故障
|
|
|
96
|
U049981
|
Invalid message received from TEL接收到TEL的无效报文
|
1. Communication failure1.通讯故障
|
|
|
97
|
U014687
|
Communication with GW lost与GW通信丢失
|
1. Communication failure1.通讯故障
|
|
|
98
|
U044781
|
Received invalid message from GW接收到GW的无效报文
|
1. Communication failure1.通讯故障
|
|
|
99
|
U17A087
|
Lost communication with combination switch MFS与组合开关MFS丢失通讯
|
1. Communication failure1.通讯故障
|
|
|
100
|
U17A081
|
Received combination switch MFS invalid message接收到组合开关MFS无效报文
|
1. Communication failure1.通讯故障
|
|
|
101
|
U015187
|
Communication with SRS lost与SRS通信丢失
|
1. Communication failure1.通讯故障
|
|
|
102
|
U045281
|
Invalid message received from SRS接收到SRS的无效报文
|
1. Communication failure1.通讯故障
|
|
|
103
|
U012987
|
Communication with BCS lost与BCS通信丢失
|
1. Communication failure1.通讯故障
|
|
|
104
|
U041881
|
Invalid message received from BCS接收到BCS的无效报文
|
1. Communication failure1.通讯故障
|
|
|
105
|
U012887
|
Communication with EPB lost与EPB通信丢失
|
1. Communication failure1.通讯故障
|
|
|
106
|
U041781
|
Received invalid message from EPB接收到EPB的无效报文
|
1. Communication failure1.通讯故障
|
|
|
107
|
P182787
|
Communication with ADC lost与ADC通信丢失
|
1. Communication failure1.通讯故障
|
|
|
108
|
P182786
|
Invalid message received from ADC接收到ADC的无效报文
|
1. Communication failure1.通讯故障
|
|
|
109
|
P187009
|
The accelerator pedal depth exceeds the limit when ReadyReady时油门踏板深度超限
|
1. The throttle sensor is abnormal or the circuit is abnormal.1.油门传感器异常或者线路异常
|
|
|
110
|
P145A94
|
Unexpected acceleration非预期加速
|
1. Power system failure1.动力系统故障
|
|
|
111
|
P145B94
|
Unexpected slowdown非预期减速
|
1. Power system failure1.动力系统故障
|
|
|
112
|
P145C94
|
Unexpected power reversal非预期动力换向
|
1. Power system failure1.动力系统故障
|