Battery inlet and outlet pipes (battery-swap)电池进出水管(换电)

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，使整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the front compartment front lower cover panel assembly2. 拆卸机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

3. Drain the coolant from the temperature control system3. 排放温控系统冷却液 Reference: Temperature control system coolant参考：温控系统冷却液

4. Disassemble the battery pack assembly (battery-swap version)4. 拆卸电池组箱总成(换电版) Reference: Battery pack assembly (battery-swap version)参考：电池组箱总成(换电版)

5. Remove the battery inlet and outlet pipes5. 拆卸电池进出水管

1 Disconnect battery inlet and outlet pipe connectors A and B.断开电池进出水管接头A、B。

2 Remove the fixing bolt ①.拆卸固定螺栓①。 Recommended tools: 10mm socket推荐工具：10mm套筒

3 Remove the 4 fixing bolts ①, disconnect water pipes A and B, and remove the battery inlet and outlet pipes.拆卸4颗固定螺栓①，断开水管A、B，取下电池进出水管。 Recommended tools: 10mm socket推荐工具：10mm套筒

Installation procedure安装程序

1. Install battery inlet and outlet pipes1. 安装电池进出水管

1 Place and adjust the battery inlet and outlet pipes to the installation position, and connect the battery inlet and outlet pipe connectors A and B.放置并调整电池进出水管到安装位置，连接电池进出水管接头A、B。 2 Install the quick-change water connector bracket to the body, install 4 fixing bolts ① and tighten them.安装快换水连接器支架到车身，安装4颗固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m

3 Install the fixing bolts ① and tighten them.安装固定螺栓①并紧固。 Recommended tools: 10mm socket推荐工具：10mm套筒 Torque requirement: 6-10N·m扭矩要求：6-10N•m

4 Connect the battery inlet and outlet pipe connectors A and B.连接电池进出水管接头A、B。

2. Install the battery pack assembly (battery-swap version)2. 安装电池组箱总成(换电版) Reference: Battery pack assembly (battery-swap version)参考：电池组箱总成(换电版)

3. Fill the temperature control system coolant3. 加注温控系统冷却液 Reference: Temperature control system coolant参考：温控系统冷却液

4. Install the front compartment front lower cover panel assembly4. 安装机舱前下护板总成 Reference: Front compartment front lower cover panel assembly参考：机舱前下护板总成

5. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, check that the cooling system should be working normally5. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，检查冷却系统应正常工作