Side left rear quarter window assembly侧围左后三角窗总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Park the vehicle on a flat road, activate the parking brake, and turn the vehicle power supply to "OFF".将车辆停在平坦路面，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。

2. Perform protective operations2. 进行保护操作 1 Use film to cover areas in the car where broken glass may fall to prevent it from causing hidden dangers.使用薄膜覆盖车内可能掉落碎玻璃的部位，防止其造成隐患。 2 Paste protective tape on the body around the left rear quarter window assembly to prevent damage to the body surface during disassembly.在侧围左后三角窗总成四周车身上粘贴保护胶带，防止拆卸过程中损伤车身表面。

3. Remove the hatchback door sill trim panel assembly3. 拆卸掀背门门槛饰板总成 Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

4. Remove the second row seat cushion assembly4. 拆卸第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

5. Remove the left rear inner sill trim panel assembly5. 拆卸左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

6. Remove the second row left seat back assembly6. 拆卸第二排左座椅靠背总成 Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

7. Remove the trunk light7. 拆卸行李箱灯 Reference: luggage compartment light参考：行李箱灯

8. Remove the left C-pillar lower trim panel assembly8. 拆卸左C柱下饰板总成 Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

9. Remove the left C-pillar upper trim panel assembly9. 拆卸左C柱上饰板总成 Reference: Left C-pillar upper trim panel assembly参考：左C柱上饰板总成

10. Remove the side left rear quarter window assembly10. 拆卸侧围左后三角窗总成

1 Use a blade to cut a section of glass glue, and pass the piano wire from the inside of the car through the seam between the body and the left rear quarter window assembly of the side panel.使用刀片切开一段玻璃胶，从车内将钢琴线穿过车身和侧围左后三角窗总成之间的接缝。   Caution:注意： ♦  Do not damage the 6 positioning pins of the rear windshield.切勿损坏后风窗6个定位销。 2 Pull the piano wire around the side panel left rear quarter window assembly and cut the adhesive.沿侧围左后三角窗总成周围拉动钢琴线，切割粘合剂。   Caution:注意： ♦  This step requires 2 people to operate at the same time.此步骤需2人同时操作。 ♦  When cutting the side left rear quarter window assembly, be careful not to damage the paint or interior and exterior trim.切割侧围左后三角窗总成时，小心不要损坏车漆或内外饰件。 ♦  Prevent the left rear quarter window assembly from sliding down.避免左后三角窗总成滑落。

3 Use a suction cup to remove the side panel left rear quarter window assembly.使用吸盘取下侧围左后三角窗总成。   Caution:注意： ♦  The side left rear triangular window assembly is a one-time item and should be scrapped after each disassembly.侧围左后三角窗总成为一次性件，每次拆卸后应报废处理。

4 Use a scraper to remove excess adhesive from the body contact surfaces.使用刮刀清除车身接触面上多余的粘合剂。   Caution:注意： ♦  Be careful not to damage the surface of the vehicle body.小心，请勿损伤车身表面。   Note:提示： ♦  Leave about 1.0mm of adhesive on the body for better installation of the side left rear quarter window assembly.在车身上留下约1.0mm的粘合剂，以便后续更好的安装侧围左后三角窗总成。 5 Clean vehicle interior debris and body surfaces.清洁车辆内部碎屑和车身表面。

Installation procedure安装程序

1. Install the side left rear quarter window assembly1. 安装侧围左后三角窗总成

1 Use the suction cup to place the side left rear quarter window assembly into the installation position.使用吸盘将侧围左后三角窗总成放置到安装位置。   Caution:注意： ♦  Check and confirm that the entire contact surface of the edge of the side left rear quarter window assembly is smooth enough.检查并确认侧围左后三角窗总成边缘的整个接触表面足够平滑。 ♦  The left rear quarter window assembly of the side panel is a one-time use piece, and new parts should be used for each installation.侧围左后三角窗总成为一次性件，每次安装应使用新件。

2 Align the 6 positioning pins of the side left rear quarter window assembly with the mounting holes on the body.对准侧围左后三角窗总成的6个定位销和车身上的安装孔。

3 Remove the side left rear quarter window assembly again.再次取下侧围左后三角窗总成。

4 As shown in the picture, apply equal-section glass glue evenly on the body installation position.如图所示，在车身安装位置上均匀涂抹等截面玻璃胶。   Caution:注意： ♦  Do not apply glass glue on the glass, otherwise it will be difficult to find the installation location during installation.不可将玻璃胶涂抹在玻璃上，否则安装时不易寻找安装位置。

5 Use a suction cup to place the side panel left rear triangle window assembly, align the relative position marks between the side panel left rear triangle window assembly and the body, align the positioning pin mounting holes, and then gently press in along the edge.使用吸盘放置侧围左后三角窗总成，对齐侧围左后三角窗总成与车身上的相对位置标记，对齐定位销安装孔，然后沿着边缘轻轻压入。   Caution:注意： ♦  Check and confirm that the side left rear quarter window assembly is correctly installed on the body.检查并确认侧围左后三角窗总成正确安装到车身上。 ♦  Check the gap between the body and the left rear quarter window assembly of the side panel.检查车身与侧围左后三角窗总成之间的间隙。 6 Gently press the surface of the left rear quarter window assembly of the side panel to ensure that it is firmly installed on the body.轻轻按压侧围左后三角窗总成表面，确保已将其牢固安装到车身上。 7 Use a scraper to remove any excess or protruding glass glue.使用刮刀清除所有多余或突出的玻璃胶。 8 Use protective tape to secure the side panel left rear quarter window assembly until the applied sealant hardens.使用保护胶带固定侧围左后三角窗总成，直到涂抹的密封胶硬化。   Note:提示： ♦  For the minimum amount of time you need to wait before driving the vehicle, follow the glass sealant manufacturer's instructions or the corresponding instructions.有关驾驶车辆前需要等待的最少时间，请遵循玻璃密封胶厂商的说明或相应说明书的说明。 9 Remove the covering film from the car取出车内的覆盖薄膜

2. Check for water leakage (rain test)2. 检查是否漏水(淋雨试验)

1 After the sealant hardens, sprinkle water from the outside of the vehicle (10 minutes) to check and confirm whether there is water leakage. If there is water leakage, clean the water traces and replenish the glass glue in time.密封胶硬化后，从车辆外部洒水(10min)，检查并确认是否有水渗漏。若有水渗漏，则清洁水迹并及时补充玻璃胶。 2 Remove the protective tape.揭下保护胶带。

3. Install the left C-pillar upper trim panel assembly3. 安装左C柱上饰板总成 Reference: Left C-pillar upper trim panel assembly参考：左C柱上饰板总成

4. Install the left C-pillar lower trim panel assembly4. 安装左C柱下饰板总成 Reference: Left C-pillar lower trim panel assembly参考：左C柱下饰板总成

5. Install trunk light5. 安装行李箱灯 Reference: luggage compartment light参考：行李箱灯

6. Install the second row left seat back assembly6. 安装第二排左座椅靠背总成 Reference: Second row left seat back assembly参考：第二排左座椅靠背总成

7. Install the left rear inner sill trim panel assembly7. 安装左后内门槛饰板总成 Reference: Left rear inner sill trim panel assembly参考：左后内门槛饰板总成

8. Install the second row seat cushion assembly8. 安装第二排座椅坐垫总成 Reference: Second row seat cushion assembly参考：第二排座椅坐垫总成

9. Install hatchback door sill trim panel assembly9. 安装掀背门门槛饰板总成 Reference: Hatchback door sill trim panel assembly参考：掀背门门槛饰板总成

10. Connect the negative terminal of the 12V battery10. 连接蓄电池负极