Left front sliding column assembly左前滑柱总成

Removal procedure拆卸程序

1. Preparation1. 准备工作 1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。 2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。 3 Lift the vehicle.举升车辆。

2. Remove the left side cover of the wiper cover2. 拆卸雨刮盖板左侧盖板 Reference: Wiper cover left cover参考：雨刮盖板左侧盖板

3. Remove the right side cover of the wiper cover3. 拆卸雨刮盖板右侧盖板 Reference: Wiper cover right side cover参考：雨刮盖板右侧盖板

4. Remove the left scraper arm4. 拆卸左刮臂 Reference: Left scraping arm参考：左刮臂   Note:提示： ♦  Remove the right scraper arm and accessories as a whole without disassembly.将右刮臂及附件作为整体拆下，不必进行拆分。

5. Remove the right scraper arm5. 拆卸右刮臂 Reference: Right scraping arm参考：右刮臂   Note:提示： ♦  Remove the left scraper arm and accessories as a whole without disassembly.将左刮臂及附件作为整体拆下，不必进行拆分。

6. Remove the wiper cover assembly6. 拆卸雨刮盖板总成 Reference: Wiper cover参考：雨刮盖板

7. Remove the left front wheel assembly7. 拆卸左前车轮总成 Reference: Wheel assembly参考：车轮总成

8. Remove the left front drive shaft nut to remove the drive shaft from the wheel hub bearing installation position.8. 拆卸左前驱动轴螺母，使驱动轴脱离轮毂轴承安装位置 Reference: Left front drive shaft assembly参考：左前驱动轴总成   Caution:注意： ♦  Brush the locking opening of the drive shaft nut completely, otherwise the threads of the drive shaft may be damaged.完全冲开驱动轴螺母的锁止口，否则可能损坏驱动轴的螺纹。

9. Remove the left front steering knuckle assembly9. 拆卸左前转向节总成 Reference: Left front steering knuckle assembly参考：左前转向节总成   Note:提示： ♦  The left front steering knuckle assembly with front wheel hub bearing can be disassembled as a whole without disassembly.左前转向节总成带前轮毂轴承整体拆卸，不必拆分。

10. Remove the left front sliding column assembly10. 拆卸左前滑柱总成

1 Remove the 3 fixing nuts ① and remove the left front sliding column assembly A.拆卸3颗固定螺母①，取下左前滑柱总成A。 Recommended tools: 15mm socket推荐工具：15mm套筒   Caution:注意： ♦  To avoid installation errors, please make alignment marks on the relative movable parts of the left front sliding column assembly before disassembly.为避免安装错误，拆卸前请在左前滑柱总成可相对活动部位做对准标记。 ♦  When removing the upper fixing nut of the left sliding column assembly, staff should support the left sliding column assembly below to prevent the left front sliding column assembly from falling and being damaged.拆卸左滑柱总成上端固定螺母时，应有工作人员在下方托住左滑柱总成，以免左前滑柱总成掉落损坏。

Installation procedure安装程序

1. Install the left front sliding column assembly1. 安装左前滑柱总成

1 Place and adjust the left front sliding column assembly A to the installation position, install 3 fixing nuts ① and tighten them.放置并调整左前滑柱总成A到安装位置，安装3颗固定螺母①并紧固。 Recommended tools: 15mm socket推荐工具：15mm套筒 Torque requirement: 63-77N·m扭矩要求：63-77N•m   Caution:注意： ♦  To avoid installation errors, install according to the alignment marks.为避免安装错误，应按照对准标记安装。 ♦  When installing the upper fixing nut of the left front strut assembly, staff should support the strut assembly below to prevent the left front strut assembly from falling and being damaged.安装左前滑柱总成上端固定螺母时，应有工作人员在下方托住滑柱总成，以免左前滑柱总成掉落损坏。 ♦  Some models use bolts, please refer to the actual vehicle for details.部分车型使用螺栓固定，具体请以实车为准。

2. Install the left front steering knuckle assembly2. 安装左前转向节总成 Reference: Left front steering knuckle assembly参考：左前转向节总成

3. Install the left front drive shaft nut3. 安装左前驱动轴螺母 Reference: Left front drive shaft assembly参考：左前驱动轴总成

4. Install the left front wheel assembly4. 安装左前车轮总成 Reference: Wheel assembly参考：车轮总成

5. Install the wiper cover5. 安装雨刮盖板 Reference: Wiper cover参考：雨刮盖板

6. Install the right scraper arm6. 安装右刮臂 Reference: Right scraping arm参考：右刮臂

7. Install the left scraper arm7. 安装左刮臂 Reference: Left scraping arm参考：左刮臂

8. Install the right side cover of the wiper cover8. 安装雨刮盖板右侧盖板 Reference: Wiper cover right side cover参考：雨刮盖板右侧盖板

9. Install the left side cover of the wiper cover9. 安装雨刮盖板左侧盖板 Reference: Wiper cover left cover参考：雨刮盖板左侧盖板

10. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, conduct a road test and check10. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，路试检查