Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。
2 Disconnect the negative terminal of the 12V battery.断开蓄电池负极。
3 Lift the vehicle.举升车辆。
|
|
|
2. Remove the right front wheel assembly2. 拆卸右前车轮总成
|
|
|
3. Remove the front compartment front lower cover panel assembly3. 拆卸机舱前下护板总成
|
|
|
4. Remove the right front drive shaft assembly4. 拆卸右前驱动轴总成
|
|
|
1 Use screwdriver A to insert into the part shown in the figure to fix the brake disc, and install 2 wheel assembly fixing bolts ①.使用螺丝刀A插入图示部位对制动盘进行固定，安装2颗车轮总成固定螺栓①。
|
|
Recommended tools: Phillips screwdriver, 17mm socket推荐工具：十字螺丝刀、17mm套筒 |
|
|
Caution:注意： |
|
♦
|
Install the 2 wheel assembly fixing bolts to prevent the brake disc fixing bolts from breaking due to excessive force during disassembly.安装2颗车轮总成固定螺栓，防止拆卸时用力过大导致制动盘固定螺栓断裂。 |
|
♦
|
Use a screwdriver to insert into the front brake disc and limit the rotation of the front brake disc to facilitate removal of the driveshaft nut.使用螺丝刀插入前制动盘，限制前制动盘的转动以方便拆卸驱动轴螺母。 |
|
|
|
|
|
2 Use a chisel and a hammer to pry open the locking part of the drive shaft nut and remove the drive shaft nut ①; remove the screwdriver A and remove the 2 wheel assembly fixing bolts ②.使用錾子和铁锤，撬开驱动轴螺母的锁紧部位，拆卸驱动轴螺母①；取下螺丝刀A，拆卸2颗车轮总成固定螺栓②。
|
|
Recommended tools: 36mm socket, 17mm socket, chisel, hammer推荐工具：36mm套筒、17mm套筒、錾子、铁锤 |
|
|
|
Caution:注意： |
|
♦
|
Brush the locking opening of the drive shaft nut completely, otherwise the threads of the drive shaft may be damaged.完全冲开驱动轴螺母的锁止口，否则可能损坏驱动轴的螺纹。 |
|
|
|
|
|
3 Remove the fixing nut ① and disengage the front transverse stabilizer rod assembly A from the installation position.拆卸固定螺母①，使前横向稳定杆拉杆总成A脱离安装位置。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
|
Caution:注意： |
|
♦
|
During operation, if the ball head rotates with the nut, use a 6mm Allen wrench to secure it.操作时，如果球头随螺母一起转动，则使用6mm内六角扳手对其进行固定。 |
|
|
|
|
|
4 Remove the fixing nut ① and use the ball head removal tool to disengage the steering crossbar ball head A from the installation position.拆卸固定螺母①，使用球头拆卸工具，使转向横杆球头A脱离安装位置。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
Special Tools: Ball Head Removal Tool专用工具：球头拆卸工具 |
|
|
|
5 Remove the 3 fixing nuts ① to disengage the right front lower swing arm assembly from its installation position.拆卸3颗固定螺母①，使右前下摆臂总成脱离安装位置。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
|
6 Install the wheel hub side drive shaft removal tool A and use 3 wheel assembly fixing bolts ① to fix the wheel hub side drive shaft removal tool A.安装轮毂侧驱动轴拆卸工具A，使用3颗车轮总成固定螺栓①固定轮毂侧驱动轴拆卸工具A。
|
|
Recommended tools: 17mm socket推荐工具：17mm套筒 |
|
|
Special Tool: Hub Side Drive Shaft Removal Tool专用工具：轮毂侧驱动轴拆卸工具 |
|
|
|
7 Turn the bolt ① of the drive shaft removal tool on the hub side clockwise to disengage the drive shaft from the steering knuckle.顺时针拧动轮毂侧驱动轴拆卸工具的螺栓①，使驱动轴从转向节中脱出。
|
|
Recommended tools: 19mm socket推荐工具：19mm套筒 |
|
|
|
Caution:注意： |
|
♦
|
When disassembling the drive shaft, do not place the drive shaft universal joint at an excessive angle.拆卸驱动轴时，驱动轴万向节放置的角度不要过大。 |
|
♦
|
Do not overstretch the three-ball universal joint to prevent the three-ball pin from falling off the ball cage and damaging the three-ball pin.不要过分拉伸三球销万向节，以免三球销从球笼脱落而损坏三球销。 |
|
|
|
|
|
8 Remove the three wheel assembly fixing bolts ① and remove the wheel hub side drive shaft removal tool A.拆卸3颗车轮总成固定螺栓①，取下轮毂侧驱动轴拆卸工具A。
|
|
Recommended tools: 17mm socket推荐工具：17mm套筒 |
|
|
|
9 Configuration 1: Remove the 2 fixing bolts ① and use the reducer side drive shaft removal tool to pry off the right front drive shaft assembly.配置一：拆卸2颗固定螺栓①，使用减速器侧驱动轴拆卸工具撬下右前驱动轴总成。
|
|
Recommended tools: 13mm socket推荐工具：13mm套筒 |
|
|
Special tool: Reducer side drive shaft removal tool专用工具：减速器侧驱动轴拆卸工具 |
|
|
|
Caution:注意： |
|
♦
|
After disassembling the drive shaft, use a plug cap to seal the differential oil seal to prevent oil from flowing out and dirt from entering.拆卸驱动轴后，使用堵盖对差速器油封口处进行密封，防止油液流出和污物进入。 |
|
|
|
|
|
10 Configuration 2: Remove the 2 fixing bolts ① and use the reducer side drive shaft removal tool A to pry off the right front drive shaft assembly B.配置二：拆卸2颗固定螺栓①，使用减速器侧驱动轴拆卸工具A撬下右前驱动轴总成B。
|
|
Recommended tools: 13mm socket推荐工具：13mm套筒 |
|
|
Special tool: Reducer side drive shaft removal tool专用工具：减速器侧驱动轴拆卸工具 |
|
|
|
Caution:注意： |
|
♦
|
After disassembling the drive shaft, use a plug cap to seal the differential oil seal to prevent oil from flowing out and dirt from entering.拆卸驱动轴后，使用堵盖对差速器油封口处进行密封，防止油液流出和污物进入。 |
|
|
|
Installation procedure安装程序
|
|
1. Install the right front drive shaft assembly1. 安装右前驱动轴总成
|
|
|
1 Configuration 1: Place and adjust the right front drive shaft assembly to the installation position, install 2 fixing bolts ① and tighten them.配置一：放置并调整右前驱动轴总成到安装位置，安装2颗固定螺栓①并紧固。
|
|
Recommended tools: 13mm socket推荐工具：13mm套筒 |
|
|
Torque requirement: 22-28N·m扭矩要求：22-28N•m |
|
|
|
Caution:注意： |
|
♦
|
Do not damage the differential end oil seal.请勿损坏差速器端油封。 |
|
|
|
|
|
2 Configuration 2: Place and adjust the right front drive shaft assembly A to the installation position, install 2 fixing bolts ① and tighten them.配置二：放置并调整右前驱动轴总成A到安装位置，安装2颗固定螺栓①并紧固。
|
|
Recommended tools: 13mm socket推荐工具：13mm套筒 |
|
|
Torque requirement: 22-28N·m扭矩要求：22-28N•m |
|
|
|
Caution:注意： |
|
♦
|
Do not damage the differential end oil seal.请勿损坏差速器端油封。 |
|
|
|
|
|
3 Place and adjust the right front lower swing arm assembly to the installation position, install 3 fixing nuts ① and tighten them.放置并调整右前下摆臂总成到安装位置，安装3颗固定螺母①并紧固。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
Torque requirement: 120-140N·m扭矩要求：120-140N•m |
|
|
|
4 Place and adjust the mechanical steering gear assembly tie rod A to the installation position, install the fixing nut ① and tighten it.放置并调整机械转向器总成拉杆A到安装位置，安装固定螺母①并紧固。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
Torque requirement: 81-99N·m扭矩要求：81-99N•m |
|
|
|
5 Place and adjust the front transverse stabilizer rod assembly A to the installation position, install the fixing nut ① and tighten it.放置并调整前横向稳定杆拉杆总成A到安装位置，安装固定螺母①并紧固。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
Torque requirement: 99-121N·m扭矩要求：99-121N•m |
|
|
|
Caution:注意： |
|
♦
|
During operation, if the ball head rotates with the nut, use a 6mm Allen wrench to secure it.操作时，如果球头随螺母一起转动，则使用6mm内六角扳手对其进行固定。 |
|
|
|
|
|
6 Use screwdriver A to insert into the part shown in the figure to fix the brake disc, and install 2 wheel assembly fixing bolts ①.使用螺丝刀A插入图示部位对制动盘进行固定，安装2颗车轮总成固定螺栓①。
|
|
Recommended tools: Phillips screwdriver, 17mm socket推荐工具：十字螺丝刀、17mm套筒 |
|
|
|
Caution:注意： |
|
♦
|
Use a screwdriver to insert into the front brake disc to restrict the rotation of the front brake disc to facilitate tightening of the driveshaft nut.使用螺丝刀插入前制动盘，限制前制动盘的转动以方便紧固驱动轴螺母。 |
|
|
|
|
|
7 Install the drive shaft nut ① and tighten it, remove the screwdriver A, and remove the 2 wheel assembly fixing bolts ②.安装驱动轴螺母①并紧固，取下螺丝刀A，拆卸2颗车轮总成固定螺栓②。
|
|
Recommended tools: 36mm socket, 17mm socket推荐工具：36mm套筒、17mm套筒 |
|
|
Torque requirement: 330-390N·m扭矩要求：330-390N•m |
|
|
|
Caution:注意： |
|
♦
|
The drive shaft nut is a disposable part and must be replaced after each disassembly.驱动轴螺母属于一次性件，每次拆卸后，必须更换驱动轴螺母。 |
|
|
8 Using a chisel and hammer, tighten the drive shaft nut.使用錾子和铁锤，锁紧驱动轴螺母。
|
|
Recommended tools: hammer, chisel推荐工具：铁锤、錾子 |
|
|
|
2. Install the front compartment front lower cover panel assembly2. 安装机舱前下护板总成
|
|
|
3. Install the right front wheel assembly3. 安装右前车轮总成
|
|
|
4. Land the vehicle, connect the negative terminal of the 12V battery, start the vehicle and drive away from the lift, conduct a road test and check4. 降落车辆，连接蓄电池负极，起动车辆并驶离举升机，路试检查
|
Right front driveshaft assembly右前驱动轴总成
