DTC list故障码(DTC)列表
|
No.序号 |
DTC故障码 |
Fault code description故障码描述 |
Possible reasons可能原因 |
Solution解决办法 |
|---|---|---|---|---|
|
1
|
C110016
|
ECU power supply voltage is too lowECU供电电压过低
|
1. When the power supply voltage is less than 9V, record the fault code1.当供电电压小于9V，记录故障码
|
|
|
2
|
C110017
|
ECU power supply voltage is too highECU供电电压过高
|
1. When the power supply voltage is greater than 16V, record the fault code1.当供电电压大于16V，记录故障码
|
|
|
3
|
C116096
|
Power management chip failure电源管理芯片故障
|
1. The chip detects abnormal supply voltage1.芯片检测供电电压异常
|
|
|
4
|
C116196
|
ECU EEPROM errorECU EEPROM错误
|
1.EEPROM internal verification error1.EEPROM内部校验错误
|
|
|
5
|
C116296
|
ECU stack failureECU堆栈故障
|
1.ECU stack failure1.ECU堆栈故障
|
|
|
6
|
C116396
|
ECU general memory failure_main storage failureECU一般内存故障_主存储故障
|
1. The flash data calculation verification result is inconsistent with the recorded verification code.1.flash的数据计算校验结果与记录的校验码不一致
|
|
|
7
|
C116408
|
ECU serial port communication failureECU串口通讯故障
|
1. The input comparison function of the system's main and auxiliary microcontrollers fails, and the main controller independently controls the system without functional degradation.1.系统主辅单片机输入比对功能失效，主控制器独立控制系统，无功能降级
|
|
|
8
|
C113009
|
Switch failure开关故障
|
1. The switch state is unstable; the main microcontroller cannot recognize the switch state normally.1.开关状态不稳定；主单片机无法正常识别开关状态
|
|
|
9
|
C113072
|
Switch failure_pull-up stuck开关故障_拉起卡滞
|
1. The switch state always belongs to the APPLY state1.开关状态始终属于APPLY状态
|
|
|
10
|
C113073
|
Switch failure_release stuck开关故障_释放卡滞
|
1. The switch is always in the released state1.开关始终属于释放状态
|
|
|
11
|
C11A112
|
Right actuator system failure_motor short circuit to power supply右执行器系统故障_电机对电源短路
|
1. During motor operation and self-test, MOSFET feedback does not match the electrical characteristics.1.电机运行与自检过程，MOSFET反馈与电气特性不符
|
|
|
12
|
C11A212
|
Left actuator system failure_motor short circuit to power supply左执行器系统故障_电机对电源短路
|
1. During motor operation and self-test, MOSFET feedback does not match the electrical characteristics.1.电机运行与自检过程，MOSFET反馈与电气特性不符
|
|
|
13
|
C11A111
|
Right actuator system failure_short circuit右执行器系统故障_短路
|
1. During motor operation, the current is greater than the set short-circuit threshold. (Example: short-circuit the positive and negative poles of the motor and activate the EPB switch to perform clamping or releasing operations)1.电机动作过程中电流大于设定短路阈值。（例：短接电机正负极，动作EPB开关执行夹紧或释放操作）
|
|
|
14
|
C11A211
|
Left actuator system failure_short circuit左执行器系统故障_短路
|
1. During motor operation, the current is greater than the set short-circuit threshold. (Example: short-circuit the positive and negative poles of the motor and activate the EPB switch to perform clamping or releasing operations)1.电机动作过程中电流大于设定短路阈值。（例：短接电机正负极，动作EPB开关执行夹紧或释放操作）
|
|
|
15
|
C11A194
|
Right actuator system failure_operation timeout右执行器系统故障_运行超时
|
1. When the motor is preparing to clamp or release, or is being clamped or released, the running time exceeds the design time.1.电机在准备夹紧或释放中、正在夹紧或释放中运行时间超出设计时间
|
|
|
16
|
C11A294
|
Left actuator system failure_operation timeout左执行器系统故障_运行超时
|
1. When the motor is preparing to clamp or release, or is being clamped or released, the running time exceeds the design time.1.电机在准备夹紧或释放中、正在夹紧或释放中运行时间超出设计时间
|
|
|
17
|
C11A113
|
Right actuator system failure_open circuit右执行器系统故障_开路
|
1. The motor operation feedback is inconsistent with the electrical characteristics; when the motor does not move, the actuator has an open circuit fault.1.电机运行反馈与电气特性不符；电机未动作时，执行机构出现开路故障
|
|
|
18
|
C11A213
|
Left actuator system failure_open circuit左执行器系统故障_开路
|
1. The motor operation feedback is inconsistent with the electrical characteristics; when the motor does not move, the actuator has an open circuit fault.1.电机运行反馈与电气特性不符；电机未动作时，执行机构出现开路故障
|
|
|
19
|
C11A192
|
Right actuator system failure_inspection failure右执行器系统故障_巡检故障
|
1. Abnormality of actuator circuit1.执行器电路异常
|
|
|
20
|
C11A292
|
Left actuator system failure_inspection failure左执行器系统故障_巡检故障
|
1. Abnormality of actuator circuit1.执行器电路异常
|
|
|
21
|
C11A149
|
Right actuator system failure_right motor drive chip failure右执行器系统故障_右电机驱动芯片故障
|
1. The output signal of the motor driver chip is abnormal.1.电机驱动芯片输出信号异常
|
|
|
22
|
C11A249
|
Left actuator system failure_Left motor drive chip failure左执行器系统故障_左电机驱动芯片故障
|
1. The output signal of the motor driver chip is abnormal.1.电机驱动芯片输出信号异常
|
|
|
23
|
C11A11C
|
Right actuator system failure_motor voltage abnormality右执行器系统故障_电机电压异常
|
1. When the motor operates, the voltage difference between the two ends of the motor is less than the set threshold.1.电机动作时，电机两端电压差小于设定的阈值
|
|
|
24
|
C11A21C
|
Left actuator system failure_motor voltage abnormality左执行器系统故障_电机电压异常
|
1. When the motor operates, the voltage difference between the two ends of the motor is less than the set threshold.1.电机动作时，电机两端电压差小于设定的阈值
|
|
|
25
|
C117055
|
Software configuration error软件配置错误
|
1.ECU software configuration is not configured1.ECU软件配置未配置
|
|
|
26
|
C110001
|
Unexpected power failure意外掉电故障
|
1. System unexpected power outage1.系统意外断电
|
|
|
27
|
C11D001
|
Ignition circuit inconsistency fault点火线路不一致故障
|
1.The CAN ignition signal is inconsistent with the hard-wired ignition signal1.CAN点火信号与硬线点火信号不一致
|
|
|
28
|
C116594
|
FailSfe shuts down abnormallyFailSfe异常关断
|
1. There is a problem with the FS pin. At this time, the control power of the pre-drive circuit is forced to switch to the auxiliary system. If it is detected, it will be recorded.1.FS引脚出现问题，此时预驱电路控制权强制切换至辅系统，检测到就记录
|
|
|
29
|
C110104
|
Auxiliary system offline failure辅系统掉线故障
|
1. The serial port or IO port of the auxiliary system is abnormal.1.辅系统串口或IO口异常
|
|
|
30
|
C11B193
|
Left actuator PBC failure - motor cannot start左侧执行器PBC故障-电机无法启动
|
1. The motor current of the EPB caliper assembly is too low and cannot be started.1.EPB卡钳总成电机电流过低,无法启动
|
|
|
31
|
C11B293
|
Right actuator PBC failure - motor cannot start右侧执行器PBC故障-电机无法启动
|
1. The motor current of the EPB caliper assembly is too low and cannot be started.1.EPB卡钳总成电机电流过低,无法启动
|
|
|
32
|
C11B111
|
Left actuator PBC failure - motor short circuit or stalled左侧执行器PBC故障-电机短路或堵转
|
1.EPB caliper assembly motor current is too high1.EPB卡钳总成电机电流过高
|
|
|
33
|
C11B211
|
Right actuator PBC failure - motor short circuit or stalled右侧执行器PBC故障-电机短路或堵转
|
1.EPB caliper assembly motor current is too high1.EPB卡钳总成电机电流过高
|
|
|
34
|
C11B174
|
Left actuator PBC failure - slipping when clamping左侧执行器PBC故障-夹紧时打滑
|
1. The increase in clamping force cannot be detected when the EPB caliper is clamped.1.EPB卡钳夹紧时无法检测到夹紧力的提升
|
|
|
35
|
C11B274
|
Right actuator PBC failure - slipping when clamping右侧执行器PBC故障-夹紧时打滑
|
1. The increase in clamping force cannot be detected when the EPB caliper is clamped.1.EPB卡钳夹紧时无法检测到夹紧力的提升
|
|
|
36
|
C11B177
|
Left actuator PBC failure - insufficient clamping force左侧执行器PBC故障-夹紧力不足
|
1.EPB caliper cannot reach the preset braking force1.EPB卡钳无法达到预设制动力
|
|
|
37
|
C11B277
|
Right actuator PBC failure - insufficient clamping force右侧执行器PBC故障-夹紧力不足
|
1.EPB caliper cannot reach the preset braking force1.EPB卡钳无法达到预设制动力
|
|
|
38
|
C11B163
|
Left actuator PBC failure - release timeout左侧执行器PBC故障-释放超时
|
1. During motor operation and self-test, MOSFET feedback does not match the electrical characteristics.1.电机运行与自检过程，MOSFET反馈与电气特性不符
|
|
|
39
|
C11B263
|
Right actuator PBC failure - release timeout右侧执行器PBC故障-释放超时
|
1. During motor operation and self-test, MOSFET feedback does not match the electrical characteristics.1.电机运行与自检过程，MOSFET反馈与电气特性不符
|
|
|
40
|
C11B149
|
Left actuator PBC failure - internal resistance is too large左侧执行器PBC故障-内阻过大
|
1. During motor operation and self-test, MOSFET feedback does not match the electrical characteristics.1.电机运行与自检过程，MOSFET反馈与电气特性不符
|
|
|
41
|
C11B249
|
Right actuator PBC failure - internal resistance is too large右侧执行器PBC故障-内阻过大
|
1. During motor operation and self-test, MOSFET feedback does not match the electrical characteristics.1.电机运行与自检过程，MOSFET反馈与电气特性不符
|
|
|
42
|
C11B196
|
Left actuator PBC failure - excessive idling resistance左侧执行器PBC故障-空转阻力过大
|
1. During motor operation and self-test, MOSFET feedback does not match the electrical characteristics.1.电机运行与自检过程，MOSFET反馈与电气特性不符
|
|
|
43
|
C11B296
|
Right actuator PBC failure - excessive idling resistance右侧执行器PBC故障-空转阻力过大
|
1. During motor operation and self-test, MOSFET feedback does not match the electrical characteristics.1.电机运行与自检过程，MOSFET反馈与电气特性不符
|
|
|
44
|
C11B194
|
Left actuator PBC failure - limited movement左侧执行器PBC故障-动作受限
|
1. Open circuit during motor operation1.电机运行过程中开路
|
|
|
45
|
C11B294
|
Right actuator PBC failure - limited movement右侧执行器PBC故障-动作受限
|
1. Open circuit during motor operation1.电机运行过程中开路
|
|
|
46
|
C11B017
|
Actuator PBC failure - voltage too high执行器PBC故障-电压过高
|
1. The power supply voltage exceeds 16.5V1.供电电压超过16.5V
|
|
|
47
|
C11B016
|
Actuator PBC failure - voltage is too low执行器PBC故障-电压过低
|
1. The supply voltage is lower than 8.5V1.供电电压低于8.5V
|
|
|
48
|
C11B076
|
Actuator PBC failure - assembly test not performed执行器PBC故障-未执行装配检测
|
1. Assembly inspection not performed1.未执行装配检测
|
|
|
49
|
C11B094
|
Actuator PBC failure - caliper in service release mode执行器PBC故障-卡钳处于服务释放模式
|
1. The system enters service release mode1.系统进入服务释放模式
|
|
|
50
|
U007388
|
bus off总线关闭
|
1.Circuit short circuit, open circuit or other1.电路短路、断路或其他
|
|
|
51
|
U012987
|
BCS node communication timeout (0x267, 0x160, 0x166)BCS节点通信超时（0x267、0x160、0x166）
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.BCS node failure5.BCS节点故障
|
||||
|
6.BCS network is unstable6.BCS网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
52
|
U108087
|
VCU node communication timeout (0x338, 0x1C5, 0x2C2, 0x17B)VCU节点通信超时（0x338、0x1C5、0x2C2、0x17B）
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.VCU node failure5.VCU节点故障
|
||||
|
6.VCU network is unstable6.VCU网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
53
|
U014687
|
GWM node communication timeout (0x35A, 0x083, 0x375, 0x3AC, 0x3AB, 0x208)GWM节点通信超时(0x35A、0x083、0x375、0x3AC、0x3AB、0x208)
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.GWM node failure5.GWM节点故障
|
||||
|
6.GWM network is unstable6.GWM网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
54
|
U181087
|
ADC node communication timeout (0x17C)ADC节点通信超时（0x17C）
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.ADC node failure5.ADC节点故障
|
||||
|
6.ADC network is unstable6.ADC网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
55
|
U041881
|
BCS node signal is invalid (0x267, 0x160, 0x166)BCS节点信号无效（0x267、0x160、0x166）
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.BCS node failure5.BCS节点故障
|
||||
|
6.BCS network is unstable6.BCS网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
56
|
U108081
|
The VCU node signal is invalid (0x338, 0x1C5, 0x2C2, 0x17B)VCU节点信号无效（0x338、0x1C5、0x2C2、0x17B）
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.VCU node failure5.VCU节点故障
|
||||
|
6.VCU network is unstable6.VCU网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
57
|
U044781
|
The GWM node signal is invalid (0x35A, 0x083, 0x375, 0x3AC, 0x3AB, 0x208)GWM节点信号无效(0x35A、0x083、0x375、0x3AC、0x3AB、0x208)
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.GWM node failure5.GWM节点故障
|
||||
|
6.GWM network is unstable6.GWM网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
58
|
U181081
|
ADC node signal is invalid (0x17C)ADC节点信号无效（0x17C）
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.ADC node failure5.ADC节点故障
|
||||
|
6.ADC network is unstable6.ADC网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
59
|
U015187
|
SRS node communication timeout (0x3AB, 0x208)SRS节点通信超时（0x3AB、0x208）
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.SRS node failure5.SRS节点故障
|
||||
|
6.SRS network is unstable6.SRS网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|
||||
|
60
|
U045281
|
The SRS node signal is invalid (0x3AB, 0x208)SRS节点信号无效（0x3AB、0x208）
|
1.CAN hardware failure, including CAN-H and CAN-L1.CAN硬件故障，包括CAN-H和CAN-L
|
|
|
2. The bus line is disconnected2.总线线路断线
|
||||
|
3. The bus is disturbed3.总线受到干扰
|
||||
|
4. Controller abnormality4.控制器异常
|
||||
|
5.SRS node failure5.SRS节点故障
|
||||
|
6.SRS network is unstable6.SRS网络不稳定
|
||||
|
7. Other reasons: such as whether there is condensation inside the controller, condensation or evaporation of water droplets, grounding interference, etc.7.其它原因：如控制器内部是否有凝露，水滴凝结或者蒸发、接地干扰等等
|