Troubleshooting › Brake control system › Diagnosis
C110016-故障诊断 · T00607764

 C110016 - TroubleshootingC110016-故障诊断

Fault code description故障码说明
DTC故障码(DTC)
Fault code description故障码描述
Possible cause of failure可能故障原因
C110016
ECU power supply voltage is too lowECU供电电压过低
1. When the power supply voltage is less than 9V, record the fault code1.当供电电压小于9V，记录故障码
Troubleshooting steps故障诊断步骤
①Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Go to step 2.去步骤2。
②Check 12V battery voltage检查蓄电池电压
1. Power status is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”,断开蓄电池负极。
2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。
Standard voltage value: about 12.5V标准电压值：约12.5V
Are the test results normal?检查结果是否正常？
Yes是 Go to step 4.去步骤4。
No否 Go to step 3.去步骤3。
③Check DCDC output voltage检查DCDC输出电压
1. The vehicle is powered on.车辆上电。
2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。
Standard voltage value: about 14V标准电压值：约14V
Are the test results normal?检查结果是否正常？
Yes是 Charge the 12V battery and replace it if necessary.对蓄电池进行充电，必要时更换蓄电池。
No否 Inspect DCDC and its lines.检修DCDC及其线路。
④Check the supply voltage of the electronic parking control unit检查电子驻车控制单元供电电压
Graphic
1. The vehicle is powered on.车辆上电。
2. Use a digital multimeter to measure the voltage between pins 1/3/5/24 of the electronic parking control unit harness connector BD92 and ground.用数字万用表测量电子驻车控制单元线束接插件BD92的1/3/5/24号针脚与接地之间的电压。
Standard voltage value: about 14V标准电压值：约14V
Are the test results normal?检查结果是否正常？
Yes是 Go to step 5.去步骤5。
No否 Inspect and repair the power supply line of the electronic parking control unit.检修电子驻车控制单元供电线路。
⑤Replace electronic parking control unit更换电子驻车控制单元
1. Replace the electronic parking control unit with a new one and check whether the fault code and symptoms are eliminated.更换新的电子驻车控制单元，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Look for causes from other symptoms.从其他症状查找原因。
  Caution:注意：
♦  After replacing the electronic parking control unit, you need to use a diagnostic tool to recalibrate the electronic parking control unit.更换电子驻车控制单元后，需用诊断仪对电子驻车控制单元重新标定。