DTC list故障码(DTC)列表
|
No.序号 |
DTC故障码 |
Fault code description故障码描述 |
Possible reasons可能原因 |
Solution解决办法 |
|---|---|---|---|---|
|
1
|
U014687
|
Gateway (GWM) node communication lost网关（GWM）节点通讯丢失
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the CAN line is short-circuited or short-circuited to power or ground.2.CAN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects CAN communication?3.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
2
|
U015587
|
BCAN Ignition Control Module (ICM) node communication lostBCAN的点火控制模块（ICM）节点通讯丢失
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the CAN line is short-circuited or short-circuited to power or ground.2.CAN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects CAN communication?3.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
3
|
U016487
|
BCAN HVACF node communication lostBCAN的HVACF节点通讯丢失
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the CAN line is short-circuited or short-circuited to power or ground.2.CAN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects CAN communication?3.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
4
|
U023187
|
RLS node communication lostRLS节点通讯丢失
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
5
|
U007480
|
BCAN busLimpHomeBCAN总线LimpHome
|
1. Whether the CAN line is short-circuited or short-circuited to power or ground.1.CAN线路是否发生短接或短路电源、地的故障情况
|
|
|
2. Is there strong electromagnetic interference around the ECU that affects CAN communication?2.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
6
|
U007388
|
BCAN bus BUS OFFBCAN总线BUS OFF
|
1. Whether the CAN line is short-circuited or short-circuited to power or ground.1.CAN线路是否发生短接或短路电源、地的故障情况
|
|
|
2. Is there strong electromagnetic interference around the ECU that affects CAN communication?2.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
7
|
U042381
|
The ICM node message ICM_TotalOdometer data is invalid received on BCANBCAN上收到ICM节点消息ICM_TotalOdometer数据无效
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the CAN line is short-circuited or short-circuited to power or ground.2.CAN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects CAN communication?3.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
8
|
U045281
|
Received GW_SRS_1 message SRS_CrashOutputSt data is invalid收到GW_SRS_1消息SRS_CrashOutputSt数据无效
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the CAN line is short-circuited or short-circuited to power or ground.2.CAN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects CAN communication?3.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
9
|
U041881
|
The GW node message GW_BCS_2_B.BCS_VehSpd or GW_BCS_2_B.BCS_VehSpdVD data received from BCAN is invalid.收到BCAN的GW节点消息GW_BCS_2_B.BCS_VehSpd or GW_BCS_2_B.BCS_VehSpdVD数据无效
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the CAN line is short-circuited or short-circuited to power or ground.2.CAN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects CAN communication?3.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
10
|
U201088
|
BCM cannot send master node request on LIN1BCM无法在LIN1上发送主节点请求
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
11
|
U202481
|
RLS invalid frame received收到RLS无效帧
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
12
|
B111000
|
Rain sensor error雨量传感器错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
13
|
B111100
|
Light sensor error灯光传感器错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
14
|
B11124B
|
RLS overtemperatureRLS过温
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
15
|
B111217
|
RLS overvoltageRLS过压
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
16
|
U201781
|
RLS node communication lost (error response)RLS节点通讯丢失（错误响应）
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
17
|
B111200
|
RLS calibration errorRLS校准错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
18
|
B111205
|
RLS programming errorsRLS编程错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
19
|
B110017
|
Voltage is too high电压过高
|
1. There is a problem with the 12V battery1.蓄电池有问题
|
|
|
2.ECU power supply pin problem2.ECU供电脚问题
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
20
|
B110016
|
Voltage too low电压过低
|
1. There is a problem with the 12V battery1.蓄电池有问题
|
|
|
2. ECU power supply pin connection problem2.ECU供电管脚连接问题
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
21
|
B114077
|
Driver's central locking command error (DriverDoorLockStSwitch)主驾中控锁命令错误(DriverDoorLockStSwitch)
|
1. Pin connection problem1.管脚连接问题
|
|
|
22
|
B114211
|
Wiper intermittent time adjustment input terminal short to ground雨刮间歇时间调节输入端短地
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. Motor abnormality2.电机异常
|
||||
|
23
|
B11A02A
|
Front wiper output stalled前雨刮输出堵转
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. Motor abnormality2.电机异常
|
||||
|
24
|
B11F012
|
The output of the front wiper power supply terminal is short to the power supply (low-side drive)前雨刮供电端输出短到电源（低边驱动）
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. Motor abnormality2.电机异常
|
||||
|
25
|
B11F112
|
Front wiper speed output short to power (low side drive)前雨刮速度输出短到电源（低边驱动）
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. Motor abnormality2.电机异常
|
||||
|
26
|
B11C613
|
Right rear steering A light feedback line open circuit右后转向A灯反馈线开路
|
1. There is a problem with the light module1.灯组模块出问题
|
|
|
2. There is a problem with the feedback line wiring2.反馈线路接线出问题
|
||||
|
27
|
B11C611
|
The right rear turn signal A light feedback line is short-circuited to ground.右后转向A灯反馈线短路到地
|
1. There is a problem with the light module1.灯组模块出问题
|
|
|
2. There is a problem with the feedback line wiring2.反馈线路接线出问题
|
||||
|
28
|
B11C413
|
Left rear steering A light feedback line open circuit左后转向A灯反馈线开路
|
1. There is a problem with the light module1.灯组模块出问题
|
|
|
2. There is a problem with the feedback line wiring2.反馈线路接线出问题
|
||||
|
29
|
B11C411
|
The left rear turn A light feedback line is short-circuited to ground.左后转向A灯反馈线短路到地
|
1. There is a problem with the light module1.灯组模块出问题
|
|
|
2. There is a problem with the feedback line wiring2.反馈线路接线出问题
|
||||
|
30
|
B11B519
|
High-side brake light output is above threshold (high-side drive)高位刹车灯输出高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
31
|
B11B219
|
Left high beam output is above threshold (high side drive)左远光灯输出高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
32
|
B11B319
|
Right high beam output is above threshold (high side drive)右远光灯输出高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
33
|
B11B019
|
Left low beam output is above threshold (high-side drive)左近光灯输出高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
34
|
B11B119
|
Right low beam output is above threshold (high side drive)右近光灯输出高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
35
|
B11E612
|
Dome light output short to power supply (low side driven)顶灯输出短到电源（低边驱动）
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
36
|
B11D018
|
The output current of the left front position lamp is lower than the threshold (high-side drive)左前位置灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2. 灯具出问题
|
||||
|
37
|
B11D019
|
The output current of the left front position lamp is higher than the threshold (high-side drive)左前位置灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
38
|
B11D118
|
The output current of the right front position lamp is lower than the threshold (high-side drive)右前位置灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
39
|
B11D119
|
The output current of the right front position lamp is higher than the threshold (high-side drive)右前位置灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
40
|
B11D218
|
The output current of the left rear position light is lower than the threshold (high-side drive)左后位置灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
41
|
B11D219
|
The output current of the left rear position lamp is higher than the threshold (high-side drive)左后位置灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
42
|
B11D318
|
The output current of the right rear position light is lower than the threshold (high-side drive)右后位置灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
43
|
B11D319
|
The output current of the right rear position light is higher than the threshold (high-side drive)右后位置灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
44
|
B11B418
|
The brake light output current is lower than the threshold (high-side drive)刹车灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
45
|
B11B419
|
The brake light output current is higher than the threshold (high-side drive)刹车灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2. 灯具出问题
|
||||
|
46
|
B11E219
|
The reversing light output current is higher than the threshold (high-side drive)倒车灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
47
|
B11D819
|
The rear fog lamp output current is higher than the threshold (high-side drive)后雾灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
48
|
B11C118
|
Right turn signal output current is lower than the threshold (high-side drive)右转向灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
49
|
B11C119
|
The output current of the right turn signal is higher than the threshold (high-side drive)右转向灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
50
|
B11C018
|
The output current of the left turn signal is lower than the threshold (high-side drive)左转向灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
51
|
B11C019
|
The output current of the left turn signal is higher than the threshold (high-side drive)左转向灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
52
|
B11B718
|
The output current of the left daytime running light is lower than the threshold (high-side drive)左日间行车灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
53
|
B11B719
|
The output current of the left daytime running light is higher than the threshold (high-side drive)左日间行车灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
54
|
B11B618
|
The output current of the right daytime running light is lower than the threshold (high-side drive)右日间行车灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
55
|
B11B619
|
The output current of the right daytime running light is higher than the threshold (high-side drive)右日间行车灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
56
|
B113011
|
High beam switch input terminal short circuit to ground远光灯开关输入端对地短路
|
1. Pin connection problem1.管脚连接问题
|
|
|
57
|
B113286
|
Turn signal switch reliability转向灯开关可信度
|
1. Pin connection problem1.管脚连接问题
|
|
|
58
|
U018487
|
ACU node communication lostACU节点通讯丢失
|
1. Whether the CAN line is short-circuited or short-circuited to power or ground.1.CAN线路是否发生短接或短路电源、地的故障情况
|
|
|
2. Is there strong electromagnetic interference around the ECU that affects CAN communication?2.ECU周边是否存在影响CAN通信的强电磁干扰
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
59
|
U120087
|
SM node communication lostSM节点通讯丢失
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
60
|
B2A0809
|
Driver's seat sensor failure主驾座椅传感器故障
|
1. Driver’s seat sensor connection problem1.主驾座椅传感器连接问题
|
|
|
2. The driver's seat sensor itself is faulty2.主驾座椅传感器自身故障
|
||||
|
3. Faulty seat sensor collected by IBCM3.IBCM采集座椅传感器故障
|
||||
|
61
|
C207051
|
TPMS calibration not completedTPMS校准未完成
|
1. Sensor problem1.传感器出问题
|
|
|
2. There is interference in the surrounding area2.周边存在干扰
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
62
|
U042481
|
Receive invalid data from HVAC从HVAC接收无效数据
|
1. Sensor problem1.传感器出问题
|
|
|
2. There is interference in the surrounding area2.周边存在干扰
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
63
|
C204062
|
Vehicle speed error for TPMS用于TPMS的车速错误
|
1. Sensor problem1.传感器出问题
|
|
|
2. There is interference in the surrounding area2.周边存在干扰
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
64
|
C201492
|
Automatic positioning failed自动定位失败
|
1. Sensor problem1.传感器出问题
|
|
|
2. There is interference in the surrounding area2.周边存在干扰
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
65
|
C201592
|
Automatic learning failed自动学习失败
|
1. Sensor problem1.传感器出问题
|
|
|
2. There is interference in the surrounding area2.周边存在干扰
|
||||
|
3. The BCM itself may be faulty.3.可能是BCM本身故障
|
||||
|
66
|
B11E419
|
The trunk light output current is higher than the threshold (high-side drive)行李箱灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
67
|
B11E519
|
The license plate light output current is higher than the threshold (high-side drive)牌照灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
68
|
B25A012
|
ACC output failureACC输出故障
|
1. Pin connection problem1.管脚连接问题
|
|
|
69
|
B25A112
|
IGN1 output failureIGN1输出故障
|
1. Pin connection problem1.管脚连接问题
|
|
|
70
|
B256146
|
EEPROM errorEEPROM错误
|
1.BCM eeprom error1.BCM eeprom 出错
|
|
|
71
|
B254300
|
FrontLeft antenna errorFrontLeft天线错误
|
1.Antenna connection problem1.天线连接问题
|
|
|
72
|
B254400
|
FrontRight antenna errorFrontRight天线错误
|
1.Antenna connection problem1.天线连接问题
|
|
|
73
|
B254600
|
Internal antenna 2 error内部天线2错误
|
1.Antenna connection problem1.天线连接问题
|
|
|
74
|
B254700
|
Internal antenna 3 error内部天线3错误
|
1.Antenna connection problem1.天线连接问题
|
|
|
75
|
B254800
|
Bumper antenna error保险杠天线错误
|
1.Antenna connection problem1.天线连接问题
|
|
|
76
|
B11B818
|
The right brake light output current is lower than the threshold (high-side drive)右刹车灯输出电流低于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
77
|
B11B819
|
The right brake light output current is higher than the threshold (high-side drive)右刹车灯输出电流高于阈值(高边驱动)
|
1. Pin connection problem1.管脚连接问题
|
|
|
2. There is a problem with the lamp2.灯具出问题
|
||||
|
78
|
B111193
|
The master node did not successfully assign an ID once主节点未成功分配一次ID
|
1. Re-initialize the ambient light1.重新做氛围灯初始化
|
|
|
79
|
B2E2C93
|
(Front) SM shade not initialized(前)SM遮阳帘未初始化
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
80
|
B2E2C91
|
(former) SM parameter check error(前)SM参数检查错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
81
|
B2E2C9C
|
(Front) SM HALL sensor error(前)SM HALL传感器错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
82
|
B2E2C71
|
(Former) SM switch sticking error(前)SM 开关粘连错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
83
|
B2E2C94
|
(Front) SM Motor Relay Error(前)SM 电机继电器错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
84
|
B2E2C1C
|
(Front) SM voltage error(前)SM 电压错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
85
|
B2E2C05
|
Rear SM sunshade not initialized后SM遮阳帘未初始化
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
86
|
B2E2D91
|
Post SM parameter check error后SM参数检查错误
|
1. There is a problem with the source node1.源节点出问题
|
Reference: B2E2D91 - Troubleshooting参考：B2E2D91-故障诊断 |
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
87
|
B2E2D9C
|
Rear SM HALL sensor error后SM HALL传感器错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
88
|
B2E2D71
|
Rear SM switch sticking error后SM 开关粘连错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
89
|
B2E2D94
|
Rear SM motor relay error后SM 电机继电器错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
90
|
B2E2D1C
|
Rear SM voltage error后SM 电压错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|
||||
|
91
|
B2E2D81
|
Received SM module response error收到SM 模块响应错误
|
1. There is a problem with the source node1.源节点出问题
|
|
|
2. Whether the LIN line is short-circuited or short-circuited to power or ground.2.LIN线路是否发生短接或短路电源、地的故障情况
|
||||
|
3. Is there strong electromagnetic interference around the ECU that affects LIN communication?3.ECU周边是否存在影响LIN通信的强电磁干扰
|
||||
|
4. It may be that the BCM itself is faulty4.可能是BCM本身故障
|