B254400 - TroubleshootingB254400-故障诊断

Fault code description故障码说明

DTC故障码(DTC)	Fault code description故障码描述	Possible cause of failure可能故障原因
B254400	FrontRight antenna errorFrontRight天线错误	1.Antenna connection problem1.天线连接问题

Troubleshooting steps故障诊断步骤

①General inspection一般检查
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Check the right front door trim panel antenna harness for damage, breakage, etc.检查右前门饰板天线线束是否存在损坏、断裂等现象。 3. Check the right front door trim panel antenna harness connector for loose connection or damage.检查右前门饰板天线线束接插件是否存在虚接、损坏等现象。 Are the test results normal?检查结果是否正常？ Yes是 Go to step 2.去步骤2。 No否 Repair or replace the right front door trim antenna harness or connector.维修或更换右前门饰板天线线束或接插件。
②Check the right front door trim antenna signal harness检查右前门饰板天线信号线束
	1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Disconnect the right front door trim antenna harness connector FR14 and the integrated body control module harness connector BD57.断开右前门饰板天线线束接插件FR14和集成式车身控制模块线束接插件BD57。 3. Use a digital multimeter to measure the resistance between pin 1/2 of FR14 and pin 26/13 of BD57.用数字万用表测量FR14的1/2号针脚与BD57的26/13号针脚之间的电阻。 Standard resistance value: <1标准电阻值：＜1Ω
	d. Use a digital multimeter to measure the resistance between pin 26/13 of BD57 and ground.d.用数字万用表测量BD57的26/13号针脚与接地之间的电阻。 Standard resistance value: >1M标准电阻值：＞1MΩ
	e. Connect the negative terminal of the 12V battery.e.连接蓄电池负极。 f. Use a digital multimeter to measure the voltage between pin 26/13 of BD57 and ground.f.用数字万用表测量BD57的26/13号针脚与接地之间的电压。 Standard voltage value: 0V标准电压值：0V Are the test results normal?检查结果是否正常？ Yes是 Go to step 3.去步骤3。 No否 Repair or replace the right front door trim antenna signal harness.维修或更换右前门饰板天线信号线束。
③Replace right front door trim antenna更换右前门饰板天线
1. Replace with a new right front door trim antenna and check whether the fault code and symptoms are eliminated.更换新的右前门饰板天线，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Go to step 4.去步骤4。
④Replacing the integrated body control module更换集成式车身控制模块
1. Replace with a new integrated body control module and check whether the fault code and symptoms are eliminated.更换新的集成式车身控制模块，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Look for causes from other symptoms.从其他症状查找原因。   Caution:注意： ♦  After replacing the integrated body control module, you need to use a diagnostic tool to recalibrate the integrated body control module.更换集成式车身控制模块后，需用诊断仪对集成式车身控制模块重新标定。