|
|
NOTE： |
|
♦
|
The disassembly and assembly procedures for the left and right rear slide column assemblies are basically the same. The following content takes the left side as an example.左、右后滑柱总成的拆装程序基本相同，下述内容以左侧为例进行操作。 |
|
|
Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置，启用驻车制动，整车电源处于“OFF”状态。
2 Lift the vehicle.举升车辆。
|
|
|
2. Remove the left rear wheel assembly2. 拆卸左后车轮总成
|
|
|
3. Disassemble the rear sliding column assembly3. 拆卸后滑柱总成
|
|
|
1 Use hydraulic bracket A to lift the installation part of the rear strut assembly.使用液压托架A托举后滑柱总成的安装部位。
|
|
Recommended tools: Hydraulic bracket推荐工具：液压托架 |
|
|
|
NOTE： |
|
♦
|
Just make the rear sliding column assembly shrink by about 2cm.使后滑柱总成收缩2cm左右即可。 |
|
|
|
|
|
2 Remove the rear strut assembly fixing bolt ① and remove the lower end of the rear strut assembly A.拆卸后滑柱总成固定螺栓①，移开后滑柱总成A下端。
|
|
Recommended tools: 21mm socket推荐工具：21mm套筒 |
|
|
|
3 Remove the 2 fixing bolts ① and remove the rear sliding column assembly A.拆卸2颗固定螺栓①，取下后滑柱总成A。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
Installation procedure安装程序
|
|
1. Install the rear sliding column assembly1. 安装后滑柱总成
|
|
|
1 Place and adjust the rear sliding column assembly A to the installation position, install 2 fixing bolts ① and tighten them.放置并调整后滑柱总成A到安装位置，安装2颗固定螺栓①并紧固。
|
|
Recommended tools: 18mm socket推荐工具：18mm套筒 |
|
|
Torque requirement: 99-121N·m扭矩要求：99-121N•m |
|
|
|
2 Place and adjust the lower end of the rear sliding column assembly A to near the installation position, slowly raise the hydraulic bracket until the installation holes correspond, install the fixing bolts ① and tighten them.放置并调整后滑柱总成A下端到安装位置附近，缓慢升起液压托架，直至安装孔相对应，安装固定螺栓①并紧固。
|
|
Recommended tools: hydraulic bracket, 21mm socket推荐工具：液压托架、21mm套筒 |
|
|
Torque requirement: 180-220N·m扭矩要求：180-220N•m |
|
|
|
3 Land slowly and remove hydraulic bracket A.缓慢降落并移出液压托架A。
|
|
|
2. Install the left rear wheel assembly2. 安装左后车轮总成
|
|
|
3. Land the vehicle, start the vehicle and drive off the lift, conduct road test and check3. 降落车辆，起动车辆并驶离举升机，路试检查
|
Rear sliding column assembly后滑柱总成
