Removal procedure拆卸程序
|
|
1. Preparation1. 准备工作
1 Drive the vehicle into the lift position, activate the parking brake, and put the vehicle power supply in the "OFF" state.将车辆驶入举升机举升位置,启用驻车制动,整车电源处于“OFF”状态。
2 Lift the vehicle.举升车辆。
|
|
|
2. Remove the left front wheel assembly2. 拆卸左前车轮总成
|
|
|
3. Remove the left front caliper assembly3. 拆卸左前卡钳总成
|
|
|
1 Remove the left front brake hose hollow bolt ①.拆卸左前制动软管空心螺栓①。
|
|
Recommended tools: 11mm socket推荐工具:11mm套筒 |
|
|
Caution:注意: |
|
♦
|
Block the brake hose to prevent brake fluid from flowing out.堵塞制动软管,避免制动液流出。 |
|
♦
|
Brake fluid is corrosive, so do not contaminate other parts of the vehicle with brake fluid.制动液具有腐蚀性,不要将制动液沾染到车辆其他部位。 |
|
|
|
|
|
2 Remove the 2 fixing bolts ① and remove the left front caliper assembly A.拆卸2颗固定螺栓①,取下左前卡钳总成A。
|
|
Recommended tools: 21mm socket推荐工具:21mm套筒 |
|
|
Caution:注意: |
|
♦
|
When disassembling, first use a screwdriver to pry the friction plate to reset the brake piston slightly. Be careful not to damage the brake disc.拆卸时先使用螺丝刀撬动摩擦片,使制动活塞进行稍许复位,注意不要损坏制动盘。 |
|
|
|
Installation procedure安装程序
|
|
1. Install the left front caliper assembly1. 安装左前卡钳总成
|
|
|
1 Place and adjust the left front caliper assembly A to the installation position, install 2 fixing bolts ① and tighten them.放置并调整左前卡钳总成A到安装位置,安装2颗固定螺栓①并紧固。
|
|
Recommended tools: 21mm socket推荐工具:21mm套筒 |
|
|
Torque requirement: 160-200N·m扭矩要求:160-200N•m |
|
|
|
2 Install the left front brake hose hollow bolt ① and tighten it.安装左前制动软管空心螺栓①并紧固。
|
|
Recommended tools: 11mm socket推荐工具:11mm套筒 |
|
|
Torque requirement: 24-30N·m扭矩要求:24-30N•m |
|
|
Caution:注意: |
|
♦
|
Be careful to install copper washers at both ends of the hollow bolts, otherwise brake fluid may leak.注意安装空心螺栓两端铜片垫圈,否则可能导致制动液泄漏。 |
|
♦
|
The copper gasket is a disposable piece and needs to be replaced.铜垫片为一次性件,需更换。 |
|
|
|
|
|
2. Add brake fluid and bleed air2. 加注制动液并排气
|
|
|
3. Install the left front wheel assembly3. 安装左前车轮总成
|
|
|
4. Land the vehicle, start the vehicle and drive off the lift, conduct road test and check4. 降落车辆,起动车辆并驶离举升机,路试检查
|