P298F16 - TroubleshootingP298F16-故障诊断

Fault code description故障码说明

DTC故障码(DTC)	Fault code description故障码描述	Possible cause of failure可能故障原因
P298F16	AGS2 voltage too low faultAGS2电压过低故障	1.AGS2 failure1.AGS2故障

Troubleshooting steps故障诊断步骤

①General inspection一般检查
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。 2. Check whether the active air intake grille wiring harness is damaged or broken.检查下主动进气格栅线束是否存在损坏、断裂等现象。 3. Check the active air intake grille harness connector to see if there is any loose connection or damage.检查下主动进气格栅线束接插件是否存在虚接、损坏等现象。 Are the test results normal?检查结果是否正常？ Yes是 Go to step 2.去步骤2。 No否 Repair or replace faulty wiring harness or connector.维修或更换故障线束或接插件。
②Check 12V battery voltage检查蓄电池电压
1. Power status is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”,断开蓄电池负极。 2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。 Standard voltage value: about 12.5V标准电压值：约12.5V Are the test results normal?检查结果是否正常？ Yes是 Go to step 4.去步骤4。 No否 Go to step 3.去步骤3。
③Check DCDC output voltage检查DCDC输出电压
1. The vehicle is powered on.车辆上电。 2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正负极之间的电压。 Standard voltage value: about 14V标准电压值：约14V Are the test results normal?检查结果是否正常？ Yes是 Charge the 12V battery and replace it if necessary.对蓄电池进行充电，必要时更换蓄电池。 No否 Inspect DCDC and its lines.检修DCDC及其线路。
④Check the 12V battery power circuit of the active air intake grille检查下主动进气格栅蓄电池电源线路
	1. Power status is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”,断开蓄电池负极。 2. Disconnect the lower active air intake grille harness connector FB26.断开下主动进气格栅线束接插件FB26。 3. Use a digital multimeter to measure the voltage between pin 4 of FB26 and ground.用数字万用表测量FB26的4号针脚与接地之间的电压。 Standard voltage value: about 12.5V标准电压值：约12.5V Are the test results normal?检查结果是否正常？ Yes是 Go to step 5.去步骤5。 No否 Repair or replace the 12V battery power harness of the active air intake grille.维修或更换下主动进气格栅蓄电池电源线束。
⑤Replacing the thermal management integrated module更换热管理集成模块
1. Replace the thermal management integrated module with a new one and check whether the fault code and symptoms are eliminated.更换新的热管理集成模块，检查故障码及症状是否排除。 Are the test results normal?检查结果是否正常？ Yes是 Fault resolved.故障排除。 No否 Look for causes from other symptoms.从其他症状查找原因。   Caution:注意： ♦  After replacing the thermal management integrated module, you need to use a diagnostic instrument to recalibrate the thermal management integrated module.更换热管理集成模块后，需用诊断仪对热管理集成模块重新标定。