Troubleshooting › Driving and parking assistance systems › Diagnosis
B1ED016-故障诊断 · T00657792

 B1ED016 - TroubleshootingB1ED016-故障诊断

Fault code description故障码说明
DTC故障码(DTC)
Fault code description故障码描述
Possible cause of failure可能故障原因
B1ED016
There is a fault in the corner radar power supply, and the circuit voltage is lower than the threshold.角雷达电源存在故障，电路电压低于门槛值
1. The voltage is lower than the diagnostic voltage lower limit1.电压低于诊断电压下限
Troubleshooting steps故障诊断步骤
①Power on check上电检查
1. Repower the vehicle, use the diagnostic tool to read and clear the fault codes, and check whether the fault codes and symptoms are eliminated.车辆重新上电，使用诊断仪读取并清除故障码，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Go to step 2.去步骤2。
②Check 12V battery voltage检查蓄电池电压
1. Power state is "OFF", disconnect the negative terminal of the 12V battery.电源状态“OFF”，断开蓄电池负极。
2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正、负极之间的电压。
Standard voltage value: about 12.5V标准电压值：约12.5V
Are the test results normal?检查结果是否正常？
Yes是 Go to step 4.去步骤4。
No否 Go to step 3.去步骤3。
③Check DCDC output voltage检查DCDC输出电压
1. Power status "ON".电源状态“ON”。
2. Use a digital multimeter to measure the voltage between the positive and negative terminals of the 12V battery.用数字万用表测量蓄电池正、负极之间的电压。
Standard voltage value: about 14V标准电压值：约14V
Are the test results normal?检查结果是否正常？
Yes是 Charge the 12V battery and replace it if necessary.对蓄电池进行充电，必要时更换蓄电池。
No否 Inspect DCDC and its lines.检修DCDC及其线路。
④Check the right front blind spot monitoring main sensor power supply line检查右前盲区监测主传感器供电线路
Graphic
1. Power status "ON".电源状态“ON”。
2. Use a digital multimeter to measure the voltage between pin 1 of the FP06 and ground.用数字万用表测量FP06的1号针脚与接地之间的电压。
Standard voltage value: about 14V标准电压值：约14V
Are the test results normal?检查结果是否正常？
Yes是 Go to step 5.去步骤5。
No否 Repair or replace the right front blind spot monitoring main sensor power supply harness.维修或更换右前盲区监测主传感器供电线束。
⑤Replace the right front blind spot monitoring main sensor更换右前盲区监测主传感器
1. Replace with a new right front blind spot monitoring main sensor and check whether the fault code and symptoms are eliminated.更换新的右前盲区监测主传感器，检查故障码及症状是否排除。
Are the test results normal?检查结果是否正常？
Yes是 Fault resolved.故障排除。
No否 Look for causes from other symptoms.从其他症状查找原因。
  Caution:注意：
♦  After replacing the main sensor for monitoring the right front blind spot, you need to use a diagnostic instrument to recalibrate the main sensor for monitoring the right front blind spot.更换右前盲区监测主传感器后，需用诊断仪对右前盲区监测主传感器重新标定。